KV8400 14" Full Extension Hold-in anti-rebound Ball Bearing Drawer Slides, Cabinet Member Unhanded Side Mount Zinc Bulk-Pack - 8400-90 14

Knape And Vogt 14 Inch Drawer Slides For Cabinets

Knape and Vogt 14 inch drawer slides give a full extension travel, so drawers can open the complete length for clear access during cabinet work and service. This cabinet member is part of the Knape and Vogt 8400 Series, so it pairs with matching drawer members in that series for consistent performance across a job. The slide is a side mount ball bearing design, which supports smooth movement along the cabinet side when properly fastened in place. The model 8400-90 14 cabinet member is non-handed, so the same part can be used on either the left or right side of the cabinet to simplify inventory and layout. An anochrome finish is applied to the slide, which provides a clean metallic appearance that matches other anochrome hardware in typical shop builds.

Key Drawer Slide Details For Project Planning

• The 14 inch length supports medium-depth cabinet drawers, so layouts using the 8400 Series can be built around a clear nominal length for drawer box sizing.
• A full extension design lets the drawer travel out roughly the full slide length, which helps expose the entire drawer interior during installation, adjustment, and everyday access.
• The side clearance of 1/2 inch plus 1/32 inch, minus 0 inch on each side provides a defined gap between drawer and cabinet, which helps during box sizing and keeps movement consistent along the run.
• A height of 1-13/16 inch sets the vertical space the slide occupies, so cabinet members and drawer members can be positioned to avoid interference with shelves or face frames.
• The 32 mm pattern on this cabinet member works with 32 mm system drilling, which ties directly into line-boring setups and speeds repeatable cabinet production.
• Lever disconnect and ball retainer latch features allow the mated drawer member to be released from the cabinet member, which aids in drawer removal for finishing, service, or replacement.

Side Mount Installation And Fastener Details

This Knape and Vogt 8400-90 14 part is a side mount cabinet member, so it fastens along the cabinet side panel instead of under the drawer, supporting straightforward alignment with common cabinet constructions. The recommended fasteners are #7 x 1/2 inch Phillips truss head screws (BST1/2X7-2C), giving an installer a clear screw size and head style to use with the countersunk or slotted areas on the member. With the 1-13/16 inch height and the defined 1/2 inch plus 1/32 inch, minus 0 inch side clearance per side, the slide geometry provides reliable reference points for marking hole positions and setting drawer box widths during layout. The 32 mm pattern makes it suitable for system-drilled cabinets, so holes can line up with standard line-boring layouts.

Using This 8400 Series Cabinet Member In Builds

Where The 8400-90 14 Cabinet Member Fits

The Knape and Vogt 8400-90 14 cabinet member is designed for side mounting in cabinet cases that accept the 8400 Series slide format, so it works wherever a 14 inch full extension travel is desired. Its non-handed design allows the same member to be installed on either side of the cabinet interior, reducing part variation on the bench and simplifying labeling. The specified side clearance of 1/2 inch plus 1/32 inch, minus 0 inch on each side gives a fixed target for drawer box width calculations, which is useful when cutting multiple drawers for the same run. Because the member height is 1-13/16 inch, it fits within many standard cabinet side spaces without encroaching excessively on vertical interior room, helping maintain storage capacity. The 32 mm pattern supports cabinets drilled on a 32 mm system, so the cabinet member can be registered to existing hole lines and set square without guesswork.

Why These Drawer Slide Details Support Consistency

The full extension design of this 14 inch 8400 Series cabinet member lets drawers extend roughly to the back of the box, so access to stored items and visibility during fit checks are not restricted by hidden areas. Lever disconnect and a ball retainer latch on the mated slide system allow the drawer member to be detached from the cabinet member, which streamlines drawer removal when finishing interiors, adjusting fronts, or servicing hardware. The anochrome finish provides a uniform, neutral metallic look across all 8400 Series parts on a project, which helps maintain a consistent appearance when cabinets are open. Using the recommended #7 x 1/2 inch Phillips truss head screws aligns the fastener head shape with the slide design, supporting a tight, flush attachment along the cabinet side. The Knape and Vogt branding and the 8400 Series designation link this cabinet member to a recognized slide family, so project planners can match it with the correct drawer member by series and length for predictable performance.

Common Questions About Knape And Vogt 8400-90 14

Choose This 14 Inch Slide For Matching 8400 Builds

The Knape and Vogt 8400-90 14 cabinet member ties directly into 8400 Series side mount ball bearing drawer slide layouts, giving a 14 inch full extension option with defined clearances. With its 1/2 inch plus 1/32 inch, minus 0 inch side clearance per side, 1-13/16 inch height, and 32 mm pattern, it fits neatly into system-drilled cabinetry and planned drawer widths. Selecting this anochrome-finished cabinet member by its 8400-90 14 designation helps align cabinet-side hardware with matching 8400 Series drawer members on projects using Knape and Vogt slides.