EPCO Recessed Pull 3-3/8" (86 mm) Long Polished Chrome , 485-PC

EPCO DP485-PC Recessed Pull For Clean Fronts

EPCO DP485-PC recessed pull is a stainless steel recessed pull that provides a low-profile way to operate doors or panels while keeping surfaces clear. The recessed design creates a pull area set into the material, which helps reduce snag points on cabinet or furniture fronts in tight spaces. The 3-3/8 inch length defines the grab opening, giving a consistent hand feel when opening or closing. The 4-1/2 inch width spreads the pull area across the face, which helps distribute user force and can support smoother motion on heavier fronts. The 1-7/16 inch projection states how far the pull extends from its mounting surface, so installers can account for clearance between adjacent doors or walls. The polished chrome finish on stainless steel delivers a bright look on the visible face while using a stainless steel base material that supports a solid metal feel at the touch point.

Key Stainless Steel Recessed Pull Details

• The stainless steel material provides a metal body for the recessed pull, which supports a solid-feeling grip point where frequent hand contact is expected on doors or drawer fronts.
• The polished chrome finish applies a bright surface treatment over the stainless steel, which helps the pull visually coordinate with other polished chrome decorative hardware on the same installation.
• The 3-3/8 inch length defines the main gripping span of the recessed pull, which provides a known hand contact area that can be centered or aligned along cabinet or panel layouts.
• The 4-1/2 inch width indicates the overall side-to-side dimension of the pull, which matters when planning spacing between multiple pulls or adjacent components on a face.
• The 1-7/16 inch projection describes how far the recessed pull stands out from the mounting surface, which helps installers account for clearance when doors or panels swing or slide past nearby surfaces.

Recessed Pull Dimensions For Practical Installation

The 3-3/8 inch length of this recessed pull gives a fixed opening size to lay out against door or drawer proportions, which supports repeatable routing or cutout setups across multiple fronts. The 4-1/2 inch width defines the footprint on the face, so fabricators can plan edge distances and spacing from neighboring hardware based on a known dimension. With a 1-7/16 inch projection from the mounting surface, the pull establishes a predictable stand-off that can be worked into clearances between opposing doors, frames, or walls. The stainless steel material and polished chrome finish describe both the structural base and visible surface, which lets installers coordinate this pull with other stainless or polished chrome components in the same project.

Using This EPCO DP Series Recessed Pull

Where The EPCO DP485-PC Recessed Pull Fits

This EPCO DP series recessed pull is a stainless steel component with a polished chrome finish, so it suits projects that call for a bright metal look on a recessed grip. The 3-3/8 inch length and 4-1/2 inch width define a medium-size pull footprint, which works on cabinet doors, drawer fronts, or panels that benefit from a recessed handhold rather than a projecting handle. Because the pull is recessed, the operating area sits within the front surface, which helps keep walk-by profiles flatter on casework or furniture in confined corridors, work areas, or tight built-ins. The defined projection of 1-7/16 inch still presents enough depth for fingers at the grip edge while maintaining controlled stand-off from the mounting surface.

Dimensional Details That Support Consistent Results

The stated 3-3/8 inch length gives installers a repeatable reference for routing or cutting the recess, which helps keep multiple doors or drawers aligned when this pull is used across a bank of cabinets. The 4-1/2 inch width dimension describes the full side-to-side requirement on the face, allowing clear planning of reveals, stile widths, or spacing relative to adjacent components in a run. With a 1-7/16 inch projection, the pull sets a known depth profile from the surface, which can be factored into door overlay decisions and swing paths so that fronts operate without interference. The stainless steel material provides a metal substrate for the recessed form, while the polished chrome finish offers a coordinating appearance with other polished chrome handles or hinges used in the same decorative hardware layout.

Common Questions About EPCO DP485-PC Recessed Pull

Select This Recessed Pull For Defined Dimensions

The EPCO DP485-PC recessed pull combines stainless steel construction, a polished chrome finish, 3-3/8 inch length, 4-1/2 inch width, and 1-7/16 inch projection, giving installers fixed dimensions and appearance for layout and routing work. These defined measurements support consistent placement across multiple doors or drawers on the same run. For projects requiring a recessed stainless steel pull with polished chrome appearance and clearly stated size, this EPCO DP series pull offers the specific dimensions needed for precise planning.