Amerock Sleek Series Satin Nickel Cabinet Pull

Amerock Sleek Series satin nickel pull is a zinc die-cast handle designed for cabinet and drawer use where a modern, streamlined profile is wanted. The 3-3/4 in (95 mm) center-to-center mounting spreads the load across the door or drawer front, which helps the hardware feel solid in everyday use. The pull length of 6-13/16 in creates generous hand clearance across wider drawer fronts, supporting a comfortable grip when opening heavier loads. A 1-1/8 in projection stands the pull off the face of the cabinet, giving enough space for fingers without overhanging into walkways. The 1/2 in width presents a slim, linear look, which suits contemporary and transitional layouts using clean edges and flat-panel fronts. The satin nickel finish delivers a muted metallic surface that pairs well with many hinge finishes and common appliance tones in the same color family.

Key Amerock Sleek Pull Details For Projects

• The zinc die-cast material provides a rigid pull body, which supports consistent feel when multiple handles are mounted across a run of cabinets.
• The satin nickel finish creates a low-glare surface, which helps the pull sit visually quiet against both painted and wood grain fronts.
• The 3-3/4 in (95 mm) center-to-center dimension sets a standard drilling pattern, which streamlines layout when repeating the pull on doors and drawers.
• The overall 6-13/16 in length spans more of the drawer face, which helps balance the look on medium-width drawers and doors.
• The 1-1/8 in projection offers space behind the pull, which aids grip for larger hands while keeping the profile close to the cabinet face.
• The 1/2 in width keeps the pull visually light, which works well where a minimalist, linear hardware style is planned.

Mounting And Alignment Details For This Pull

The 3-3/4 in (95 mm) center-to-center drilling dimension defines the mounting layout, so holes can be spaced evenly across door or drawer fronts in a straight line. This sizing also allows the pull to sit centered on many common drawer widths used in kitchen and bath runs. With a projection of 1-1/8 in, the handle stands proud of the surface enough to clear typical door profiles, supporting smooth opening without knuckles contacting the face. The 6-13/16 in overall length gives clear visual references at each end during installation, which helps align the pull parallel to the cabinet edge. The 1/2 in width keeps the contact area narrow, concentrating hand placement along the centerline of the pull for a predictable feel from cabinet to cabinet.

Using The Sleek Collection Pull In Real Jobs

Where This Amerock Satin Nickel Pull Fits Best

The Amerock Sleek Series 3-3/4 in (95 mm) center-to-center pull fits cabinets and drawers laid out for this common drilling spread, so it works smoothly in many kitchen, bath, or built-in furniture runs using that standard. The satin nickel finish supports projects where a soft metallic tone is preferred over high-shine surfaces, blending well with similar hinge and knob finishes in the same color family. Its 6-13/16 in overall length suits medium-width fronts where a shorter pull might look undersized, allowing the handle to visually anchor the face. The 1/2 in width keeps the hardware from feeling bulky on narrower doors, so one style can carry across a mix of cabinet sizes without overpowering small fronts. With a 1-1/8 in projection, the pull functions well on doors near corners or walk paths because it stays relatively close to the cabinet plane while still giving finger room.

Why These Dimensions Support Repeatable Results

The defined 3-3/4 in (95 mm) center-to-center spacing supports repeatable drilling setups, since jigs and templates can be set once and used across the full job without reconfiguring. The zinc die-cast construction gives the pull a consistent shape from piece to piece, which is important when several units line up on tall banks of drawers. The satin nickel finish helps mask fingerprints compared to higher sheen surfaces, which keeps the installation looking cleaner in high-touch areas. The 6-13/16 in length and 1/2 in width work together to create a recognizable hand position every time the pull is used, aiding muscle memory for frequent access doors. The 1-1/8 in projection establishes a fixed stand-off depth, so doors and drawers across the run present a uniform sightline when viewed along the cabinet faces.

Common Questions About This Amerock Sleek Pull

Select This Pull For Satin Nickel Cabinet Runs

The Amerock Sleek Series 3-3/4 in (95 mm) center-to-center satin nickel pull BP26135G10 combines a zinc die-cast build, 6-13/16 in length, and a 1-1/8 in projection to support consistent cabinet runs. For projects calling for this drilling pattern and finish, this pull offers a coordinated, repeatable hardware choice.