KV6400 16" Full Extension Hold-in anti-rebound Ball Bearing Drawer Slides, Unhanded Side Mount Stainless Steel Poly-Pack - 6400P SS 16
Description
Knape And Vogt 16 Inch Drawer Slides For Corrosive Use
Knape and Vogt 16 inch drawer slides in the 6400P SS 16 model give you full extension action, so the drawer travels its full length and exposes the interior, which helps in cabinet layouts where clear access to stored items keeps work moving efficiently.
The 6400 series is a side mount ball bearing drawer slide, so it mounts to the cabinet side and uses ball bearings to support the drawer, which creates a smooth running motion that holds alignment under load in typical woodworking installations.
This slide is rated at 75 lb, so the mechanism is built to handle moderate drawer loads, which matters on jobs where typical residential or light commercial storage must run reliably without being overbuilt for the application.
The design is unhanded, so the same slide works on either side of the drawer, which simplifies layout and reduces part variation on site when matching left and right installations.
The construction uses stainless steel in a stainless steel finish, so the slide resists corrosion in demanding environments, which supports applications where moisture or cleaning agents are part of normal cabinet use.
Key 6400P SS 16 Details That Help On The Job
- The KV Model 6400 slide in 16 inch length defines the pull-out distance and cabinet depth needed, which lets you plan casework dimensions so drawers open fully without overtravel or interference.
- A side clearance of 0.51 inch plus 0.030 inch minus 0 inch on each side establishes the drawer box width relative to the cabinet, which helps you size boxes accurately and avoid racking or binding during operation.
- A slide height of 1-49/64 inch sets the vertical space the slide occupies, which is important when stacking drawers or working near structural rails so components do not clash during movement.
- The 32mm pattern is provided, so the hole layout aligns with 32mm system drilling, which speeds installation in system-based cabinetry and supports repeatable positioning across multiple cabinets.
- Lever disconnect is built into this slide, so the drawer member can be separated from the cabinet member, which aids shop finishing, transport, and later service when drawers need to be removed without disturbing the cabinet.
- USDA H-1 grease is specified for this unit, so the lubrication meets USDA H-1 requirements, which matters where incidental food-area contact standards influence hardware selection in woodworking projects.
Installation Dimensions And Fastener Choices For Fit
This side mount drawer slide uses a side mount configuration, so it attaches to the vertical cabinet sides, which aligns well with standard drawer box construction and gives predictable performance when working from established cabinet layouts.
The specified side clearance of 0.51 inch plus 0.030 inch minus 0 inch per side defines a tight dimensional window, which allows you to mill drawer widths to a known target so the ball bearings run smoothly without excessive play.
The slide height of 1-49/64 inch sets the minimum vertical clearance at the mounting location, which lets you position the slide to avoid interference with drawer bottoms, stretchers, or adjacent hardware in multi-drawer stacks.
Recommended fasteners are #7 x 1/2 inch Phillips pan head, so the slide is designed around this screw size and head style, which supports solid anchoring in cabinet sides and drawer members while fitting the slide holes correctly.
Choosing This 6400 Series Slide For Real Projects
Where Knape And Vogt 16 Inch Slides Work Best
The slide uses 304 grade steel for use in corrosive application, so the stainless construction supports cabinets in environments where moisture or cleaning solutions are present, which suits woodworking jobs that need hardware stability in such conditions.
Full extension travel on this 16 inch slide lets the drawer extend its full length from the cabinet, which is valuable wherever full visual and hand access to drawer contents reduces reach-in effort and speeds repetitive tasks.
The side mount, ball bearing configuration places the mechanism along the cabinet sides using ball bearings, which helps drawers track straight under the 75 lb rating and maintains consistent feel after repeated openings.
The unhanded design means a single slide pattern installs on either side, which reduces inventory complexity in the shop and simplifies field installation because left and right components do not have to be identified separately.
USDA H-1 grease is used in the slide, so the lubricant is designated USDA H-1, which supports hardware selection in cabinet projects that take food-area lubricant requirements into account during material planning.
The stainless steel finish presents the underlying stainless steel construction, which delivers corrosion resistance for the moving members, supporting smoother long-term action in corrosive application environments typical of certain cabinets.
Details That Support Repeatable Drawer Construction
The 16 inch nominal length defines the drawer member and cabinet member geometry, which lets you standardize drawer depths across a project so openings, face layouts, and interior clearances remain consistent from unit to unit.
A side clearance of 0.51 inch plus 0.030 inch minus 0 inch each side sets a clear machining target, which allows consistent drawer box sizing so installers experience predictable slide engagement without trial-and-error adjustments.
The 1-49/64 inch slide height helps when aligning multiple drawers vertically, since it gives a fixed dimension to reference from rails or bottoms, which supports maintaining uniform reveals and minimizing interference between stacked drawers.
The 32mm pattern on the slide lines up with 32mm drilling layouts, which integrates the slide into system furniture construction and lets fabricators rely on line-boring equipment for fast, repeatable hole placement.
Lever disconnect built into the slide allows the drawer section to be separated from the cabinet section, which helps when finishing drawer boxes, adjusting fronts, or transporting cabinets because the moving parts can be handled separately.
The manufacturer part number 6400P SS 16 uniquely identifies this stainless, full extension, 16 inch 6400 series slide, which makes specifying, ordering, and reordering the same hardware straightforward across multiple woodworking projects.
Common Questions About 6400P SS 16 Drawer Slides
What type of drawer slide is the 6400P SS 16?
The 6400P SS 16 is a Knape and Vogt 6400 series side mount ball bearing drawer slide, so it supports the drawer on cabinet sides for smooth, guided movement.
What is the load rating for this drawer slide?
The 6400P SS 16 drawer slide is rated at 75 lb, which fits many residential and light commercial drawer applications that require moderate load capacity.
How long is the KV 6400P SS 16 slide?
The KV 6400P SS 16 has a 16 inch length, which sets the maximum drawer extension and guides cabinet depth planning for full extension drawers.
What side clearance does this drawer slide require?
The 6400P SS 16 requires 0.51 inch side clearance plus 0.030 inch minus 0 inch per side, guiding accurate drawer box width relative to the cabinet opening.
Which fasteners are recommended for mounting?
The Knape and Vogt 6400P SS 16 slide specifies #7 x 1/2 inch Phillips pan head fasteners, which match the slide hole pattern and support secure side mounting.
What material and finish are used on this slide?
The 6400P SS 16 uses 304 grade stainless steel in a stainless steel finish, supporting use in corrosive application environments for cabinetry and drawers.
Selecting The Right 16 Inch Stainless Slide
The Knape and Vogt 6400P SS 16 full extension side mount slide combines 16 inch travel, 75 lb rating, 304 grade stainless steel, and lever disconnect, so it fits projects needing smooth drawer access in corrosive application settings.
With defined side clearance, 32mm pattern mounting, and a USDA H-1 grease specification, this slide supports consistent fabrication and installation on cabinet jobs where dimensional control and material requirements are part of the work plan.
