Nexis Cam Adjustable Face Frame Mounting Plate, Nickel-Plated, with Pre-Mounted Wood Screws, 4mm

Nexis Face Frame Adapter Plate For Hinges

Nexis face frame adapter plate gives you a dedicated hinge mounting plate designed for face frame cabinets, so you can mount Nexis hinges to the cabinet side in a controlled, repeatable way. This Grass America hinge mounting plate is made of die-cast steel, which provides a rigid base under the hinge arm so doors track more consistently over time. The nickel-plated finish on the plate offers a clean, neutral look in the cabinet interior while maintaining the underlying steel surface. The plate affixes to the Nexis hinge via a clip on design, which lets you snap the hinge arm on and off the plate quickly during fitting or adjustment without disturbing your mounting position. This 4mm Nexis face frame plate establishes the mounting height reference for the hinge system when you are laying out a run of doors across multiple openings.

Adjustment And Mounting Features That Save Time

• The Nexis cam adjustable mounting plate has two cams, which provide defined points for height and depth adjustment so you are not relying on slotted holes during alignment.
• The cams provide plus or minus 2 mm of cam height adjustment, letting you shift the door position vertically in small increments to align reveals between doors and frames.
• The same cam system provides plus 3/minus 1 mm of cam depth adjustment, so you can move the door closer to or farther from the cabinet face frame to fine-tune overlay and close position.
• The Nexis 3D cam FF plate attaches to the cabinet side via pre-mounted wood screws, which puts the fastening points exactly where the plate is designed to bear, speeding installation on multiple openings.
• The clip on hinge interface between the die-cast plate and the Nexis hinge allows you to hang the door after the plate is fixed, which simplifies working in tight cabinetry.

Face Frame Hinge Mounting And Adjustment Setup

This 4mm Nexis face frame plate works as the mounting interface between the cabinet side and the Nexis hinge arm, so the cabinet side becomes the solid reference surface for the door. The plate uses a clip on connection to the hinge, allowing you to remove the door from the cabinet by releasing the hinge arm while the plate remains screwed to the side. The two integrated cams on the plate offer plus or minus 2 mm of height adjustment and plus 3/minus 1 mm of depth adjustment, so you can dial in the door position after the plate is fixed. The pre-mounted wood screws locate through the plate into the cabinet side, tying the die-cast steel plate directly to the case side material during mounting.

Using The Nexis 3D Cam Plate In Cabinet Runs

Where This Nexis Face Frame Plate Fits Best

The Nexis face frame adapter plate is designed for face frame cabinets where the mounting point for the hinge sits on the cabinet side, providing a defined interface for Nexis hinges in that construction. With its 4mm plate specification, this Nexis cam adjustable mounting plate sets a consistent offset from the cabinet side to the hinge arm, which is important when you want all doors in a bank to share the same geometry. The die-cast steel construction supports the hinge loading at the side of the face frame opening, which is useful on taller or heavier doors that rely on stable mounting. The nickel-plated finish on the plate presents a uniform appearance across multiple cabinets, which helps keep interiors visually consistent within a project.

How Cams And Clip On Design Support Alignment

The Nexis 3D cam FF plate uses two cams that deliver plus or minus 2 mm of cam height adjustment, so you can raise or lower the hinge arm in controlled steps to straighten reveals along the frame. The same cam layout provides plus 3/minus 1 mm of cam depth adjustment, which lets you fine-tune how far the door edge sits in relation to the face frame for an even overlay. Because the Nexis hinge affixes via a clip on design, you can remove or rehang the door multiple times while working those cam adjustments without disturbing the die-cast plate on the cabinet side. The pre-mounted wood screws tie the plate to the side panel at the same time you set your layout line, which simplifies repeating the same setup across a production run of cabinets.

Common Questions About This Nexis Mounting Plate

Selecting This Nexis Plate For Face Frames

The Nexis face frame adapter plate from Grass America pairs a 4mm plate specification with die-cast steel construction, so it creates a consistent hinge interface on the cabinet side. Its twin cams deliver plus or minus 2 mm of height adjustment and plus 3/minus 1 mm of depth adjustment, which supports precise door alignment in face frame cabinetry. The clip on Nexis hinge connection and pre-mounted wood screws streamline mounting on cabinet runs. When a project calls for Nexis hinges on face frame cabinets, this Nexis cam adjustable mounting plate provides a defined, repeatable base for the hinge arms.