Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
The Würth #7 x 1-1/4" Modified Pan Head Face Frame and Pocket-Hole Screw is sized for the most common joint in cabinet face-frame construction: 3/4-inch stock joined at the rail or stile. A Hi-Lo thread, Type 17 Auger point, and lubricated finish work together to pull hardwood joints tight with less splitting and less effort.
At 1-1/4 inches, this screw is the standard choice for pocket-hole joints in 3/4-inch face-frame material. The length provides enough thread engagement in the receiving member without over-penetrating thin stock or punching through an adjacent surface. That makes it well matched to rail-to-stile joinery and face-frame-to-box attachment where both pieces are 3/4-inch hardwood. The Hi-Lo thread is fine-pitched for hardwood, so it bites cleanly into maple, oak, cherry, and similar species without the splitting pressure that a coarse thread creates in tight grain. For softwood or sheet-good face frames, a coarse-thread screw is the better choice.
The combination of the Type 17 Auger point and the lubricated finish addresses the two main friction points in hardwood pocket-hole driving: entry resistance and seating resistance. The auger flute starts chip removal immediately, keeping the tip from stalling or wandering in dense grain. The lubricated coating lowers thread friction through the full drive stroke, so the screw reaches full depth without the head stripping under a power driver. The modified pan head seats against the pocket wall rather than digging in, which concentrates clamping force at the joint line rather than splitting the surrounding material.
Cabinet shops building face frames from hardwood species will use this screw at every pocket-hole station. It handles rail-to-stile joints, attaches finished face frames to the cabinet box, and works for any 3/4-inch hardwood joint where a pocket-hole approach is preferred over biscuits, dowels, or exposed fasteners. The 7500-count box suits production shops that cycle through face-frame screws quickly and want a single stocking unit for the most common joint size. Finish carpenters and custom builders who work in smaller runs will still find the pack quantity practical when face frames are a regular part of the project mix.
Standard coarse threads have a single high-profile helix that generates significant radial pressure in dense hardwood, which can split narrow stiles. The Hi-Lo thread alternates a tall cutting thread with a shorter stabilizing thread. The tall thread provides holding power while the shorter one fills the space between, reducing the outward force on the wood fibers. The result is a strong joint with less risk of cracking the stock near the pocket.
The Hi-Lo thread on this screw is designed for hardwood. For softwood, pine, plywood, or MDF face-frame material, a coarse-thread pocket-hole screw provides better pull-out strength in those lower-density substrates.
For 3/4-inch stock, most pocket-hole jigs are set to the 3/4-inch material thickness position. The 1-1/4-inch screw length is the standard pairing for that setting. Check the jig manufacturer's chart if you are working with a different stock thickness, since the correct length changes with material thickness.
The square recess is designed to hold the screw on a correctly sized bit, which helps with one-handed placement in tight spots. That fit depends on using a properly sized bit. A worn or off-spec bit will not provide the same retention.
When using a pocket-hole jig, the jig drill bit creates the angled pocket and pilot hole in one step before the screw is driven. No separate pilot hole is needed in the receiving member for most hardwood species when the screw enters at the correct angle.
When the job calls for clean, fast hardwood face-frame joinery and the stock is 3/4 inch, this screw is sized, threaded, and finished to do that work without drama.
Sold In: 7500 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each |  WW90260 Mfr# 0614176143961 1 | #2 x 6" Square Drive Insert Bit, 2 Piece Bit | ||||
Sold in: 1000 Each |  WW15000 Mfr# 3670000195961 1000 | Würth #7 x 1-1/4" Modified Pan Head Face Frame and Pocket-Hole Screw Square Drive - Type 17 Auger Point Hi-Lo Lubricated, 3670000195961 1000 - 1000/Box | ||||
Sold in: 1000 Each |  WW15200 Mfr# 3670000194961 1000 | Würth #7 x 1-1/2" Modified Pan Head Face Frame and Pocket-Hole Screw Square Drive - Type 17 Auger Point Hi-Lo Lubricated, 3670000194961 1000 - 1000/Box | ||||
Sold in: 6000 Each |  WW15300 Mfr# 3670000194961 6000 | Würth #7 x 1-1/2" Modified Pan Head Face Frame and Pocket-Hole Screw Square Drive - Type 17 Auger Point Hi-Lo Lubricated, 3670000194961 6000 - 6000/Box |