Square Drive Face Frame and Pocket-Hole Screw For 3/4-Inch Softwood Stock
The Würth #7 x 1-1/4 inch Modified Pan Head Face Frame and Pocket-Hole Screw is a coarse-thread fastener built for pocket-hole joinery and face frame assembly in softwood, plywood, pine, and similar sheet goods. The 1-1/4 inch length is the standard match for 3/4-inch stock joined at a pocket-hole angle, making it the right reach for the most common face frame and cabinet box joints in the shop.
Key Features
- Modified pan head seats flush against the pocket wall and pulls the joint tight without wedging or splitting the stock.
- #2 square drive is designed to hold the screw on a correctly sized bit for controlled, one-handed placement in tight cabinet interiors.
- Type 17 auger point features a longitudinal flute that clears wood fibers as the screw starts, reducing torque and split risk at entry.
- Coarse thread sized for fast, strong engagement in softwood, pine, poplar, plywood, and MDF.
- Lubricated finish lowers driving friction so the screw seats cleanly under repeated production use without burning the thread or stripping the head.
- 7,500 screws per box keeps a high-volume cabinet shop running through long production runs without restocking interruptions.
The Right Length for 3/4-Inch Stock Pocket-Hole Joints
At 1-1/4 inches, this screw is sized specifically for the pocket-hole angle through 3/4-inch material. Driven at the standard 15-degree pocket-hole pitch, that length puts the thread fully into the mating piece without breaking through the far face. The result is a tight, clean joint whether the application is a face frame rail-to-stile connection, a cabinet box corner, or a drawer box panel join. The modified pan head bearing surface pulls the two faces together evenly, and the coarse thread holds in softwood and sheet goods without requiring a pilot in the mating piece.
Drive, Point, and Finish Working Together
The #2 square drive recess is cut to hold a correctly sized bit during placement, which matters most when reaching into a cabinet box or positioning a face frame joint by hand. The Type 17 auger point carries a fluted notch near the tip that shaves wood fibers rather than compressing them, keeping entry torque low and reducing the chance of splitting near a narrow stile or a plywood edge. The lubricated finish extends that advantage across the full length of the drive: friction stays low from start to full seating, which protects both the screw head and the driving bit during the kind of repetitive cycling a production run demands.
Built for Cabinet Shops Running Softwood and Sheet-Good Frames
This screw fits shops and installers working primarily with softwood face frames, poplar or pine stiles and rails, plywood cabinet boxes, and MDF or melamine components. Coarse thread is the correct choice for these materials, where it develops strong withdrawal resistance without the fine-thread torque that can over-drive into lower-density grain. The 7,500-count box is sized for continuous production, not occasional use. If the work involves hardwood face frames in maple, oak, or cherry, a fine-thread variant is the better fit for those materials.
Common Questions
Why is 1-1/4 inch the standard length for 3/4-inch pocket-hole stock?
Pocket-hole screws enter at an angle, so the effective thread engagement in the mating piece depends on both the screw length and the pocket pitch. At the standard 15-degree angle through 3/4-inch material, a 1-1/4 inch screw puts the thread fully into the second piece without the tip emerging from the far face.
Will this screw work for hardwood face frames?
Coarse thread is optimized for softwood, plywood, pine, poplar, and MDF. For hardwood face frames in maple, oak, cherry, or walnut, a fine-thread face frame screw is the correct choice. The coarse thread can over-drive and reduce holding power in dense hardwood grain.
What does the lubricated finish do during installation?
The lubricant coating reduces friction along the thread and shank as the screw seats. This lowers driving torque, helps prevent head stripping, and extends bit life during high-volume production runs where the same motion is repeated hundreds of times.
Do I need a pocket-hole jig to use this screw?
The pocket is most commonly bored with a dedicated jig, but a jig is not strictly required. What matters is that the pocket angle and depth are correct so the screw reaches the mating piece at the right pitch. The screw itself is not jig-specific.
Is a pilot hole needed in the mating piece?
No. The Type 17 auger point is self-starting and cuts its own path into the mating piece. In softwood and sheet goods, no separate pilot is needed in the second workpiece.
A Production-Volume Pocket-Hole Screw Sized for the Job
When the work is softwood face frames, plywood cabinet boxes, and standard 3/4-inch pocket-hole joints, this 1-1/4 inch square-drive screw delivers the thread, point, and head geometry that fit the application, packed at a quantity that keeps the shop moving.
