Würth #6 x 5/8" Flat Head Hinge and Drawer Slide Installation Screw Combo Drive - Sharp Point Coarse Thread Zinc, 3670000288961 1000 - 1000/Box

Wurth #6 x 5/8 Flat Head Screw For Hardware

Wurth #6 x 5/8 flat head screw is a case hardened installation screw designed for mounting hinges and drawer slides, so it handles typical cabinet hardware fastening without deforming under normal driving torque. The flat head configuration sits flush in standard countersinks on hinge and slide plates, helping hardware sit tight to the wood for consistent reveals and smooth slide action. Its sharp point starts quickly in wood or similar substrates, which speeds repetitive installs where pre-drilling is not required by the job. The coarse thread pattern advances rapidly through material, pulling hardware snug with fewer turns, which saves time across a run of doors or drawers. A zinc finish provides a basic protective layer on the steel screw surface, supporting typical indoor woodworking environments.

Key Installation Details For Everyday Cabinet Work

• This hinge and drawer slide installation screw is described as case hardened, so the treated steel body resists head distortion and shank damage during powered driving, which supports consistent seating across many fastenings.
• The screw uses a combo drive referenced as RECEX and works with #2 Phillips drive bits for insertion, so installers can run it with common bits already in the shop for both production and field work.
• Using #2 Phillips drive bits for after market adjustment means the same bit can revisit the installed screw later, which simplifies hardware tweaks or service calls on existing cabinets.
• The sharp point and coarse thread, identified in the description, help the screw bite quickly and pull hinges or slides tight to the substrate, which reduces spin-out and aids alignment of moving hardware.
• The zinc description signals a zinc-coated surface on the screw, which adds basic corrosion resistance suitable for typical interior cabinet locations where occasional humidity is present.

Drive Fit And Handling During Installation

This hinge and drawer slide installation screw is specified for use with #2 Phillips drive bits for insertion, so it matches one of the most common driver sizes on cabinet assembly lines and in installation vans. The same #2 Phillips bit also serves for after market adjustment, so installers and service techs do not need specialty bits when tuning doors or drawer slides later. The combo drive reference RECEX in the SAP description indicates a drive style intended to accept standard #2 Phillips tooling, which keeps fastener engagement familiar when running screws by hand or with a driver. Case hardened construction supports firm bit engagement at the head without rounding as easily, which helps when backing a screw out of dense material or resetting hardware positions.

How This Screw Supports Hinge And Slide Work

Using The Screw With Hinges And Drawer Slides

The SAP and web descriptions identify this product specifically as a hinge and drawer slide installation screw, so it is sized and configured for typical hardware footprints in cabinetry and similar woodworking projects. The #6 designation defines the screw gauge, aligning with common hole diameters found in many hinge leaves and slide brackets, which helps hardware sit centered in its mounting slots. Its 5/8 inch length is suited to fastening through hinge or slide plates into cabinet frames or drawer boxes where a moderate bite is needed without excessive penetration, supporting standard cabinet side and face frame thicknesses. The flat head style is intended to seat into countersunk or tapered holes on hinges and slides, helping metal parts clamp evenly against the mounting surface for stable operation. Case hardened construction supports repeated torque cycles from powered drivers across long hinge or slide runs, which is useful on larger jobs needing consistent fastening performance. The zinc surface described in the product data supports indoor cabinet environments by providing a basic layer over the steel, which helps the screw maintain appearance where heads remain visible on light-colored hardware.

Details That Help Achieve Consistent Install Results

The screw uses #2 Phillips drive bits for insertion, so installers can maintain constant tool setups while driving rows of hinge or slide screws, which reduces bit changes and keeps workflow efficient. The same #2 Phillips drive bits are specified for after market adjustment, so a single driver setup can be used when shifting hinges to refine door gaps or adjusting slides after load-in. The sharp point detail enables the screw to start into material without wandering, which helps keep hinge and slide holes aligned with layout marks and reduces misalignment across multiple doors. Coarse threads engage material quickly, pulling hardware tight with fewer driver revolutions, which shortens each install cycle and aids in drawing slightly bowed materials into contact. Case hardened construction resists head stripping when drivers are slightly off-angle, which can occur during field installs in tight cabinet interiors or when working from a ladder. The combination of flat head geometry and coarse thread bite helps the screw maintain clamp force on hardware plates, which supports long-term stability of door swing and drawer travel under normal cabinet use.

Common Questions About This Wurth Installation Screw

Selecting This Screw For Cabinet Hardware Work

This Wurth hinge and drawer slide installation screw combines a #6 gauge, 5/8 inch length, and flat head design with a sharp point coarse thread, so it aligns with common cabinet hardware fastening needs. Case hardened construction works with #2 Phillips drive bits for both insertion and after market adjustment, which supports efficient installation and later tuning with standard tools. For projects centered on mounting hinges and drawer slides in typical indoor cabinet environments, this zinc-finished screw offers a focused option for consistent fastening performance.