Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
The Grass 6.3-7.5mm flat head euro screw is a short, coarse-thread fastener designed to mount European-style hinges, drawer slides, and shelf hardware into the pre-bored holes of 32mm system cabinet panels. At 7.5mm in length, this screw is sized for the thinner panel stock and shallow-bore hardware common in frameless cabinetry, seating flush in the flat head position without over-penetrating the material. The nickel finish coordinates with nickel-finished hardware throughout the installation.
The 32mm system builds cabinet interiors around a grid of pre-bored holes spaced 32mm apart. Hardware mounting plates, hinge baseplates, and drawer slide brackets drop into those holes and get locked down with euro screws. At 7.5mm, this screw is the short end of the euro screw range and is best matched to hardware plates going into panels on the thinner side of typical cabinet construction, or to hardware with a shallow countersink that would leave a longer screw sitting proud. If the mounting plate seats fully against the panel face and the bore depth is shallow, this length keeps the screw from pushing through the back of the panel or into a laminate face. It is not a general wood screw and is not intended for edge-joining panels or structural cabinet box assembly.
The nickel finish is a practical choice when the interior of the cabinet carries nickel-finished hardware. Cabinet interiors in contemporary and transitional kitchens often mix nickel hinges, nickel drawer slides, and nickel pulls, and hardware screws that finish in the same family keep visible fastener heads from drawing attention. The flat head profile sits flush against the bearing surface of the mounting plate, and the coarse thread provides the grip needed in the particleboard and MDF panel cores that make up most frameless cabinet boxes. The #2 Phillips drive is the most widely available drive in a cabinet shop or installation kit, so no additional bit is needed to run these alongside other hardware installation work.
Cabinet shops building frameless boxes with Grass or compatible European hardware reach for this screw when the panel thickness or hardware plate depth calls for the shorter length. Installers fitting hinges and slides on-site with pre-built cabinet cases use it the same way. The 500-piece box suits production runs where hardware is installed across many cabinets in a single session, keeping a consistent fastener and finish in every mounting position without sorting through mixed hardware.
Euro screws are designed for pre-bored 32mm system holes, not for self-starting in undrilled material. The blunt point threads cleanly into an existing bore without the risk of deflecting or splitting the surrounding panel edge.
That depends on the combined depth of your hardware plate countersink and the panel thickness. The 7.5mm length is intended for shallow mounting positions in thinner panels. If your hardware seats into a deeper bore or your panel stock is thicker, a longer euro screw in this family will give you more thread engagement.
Many European hardware brands share the 32mm system bore standard, and the 6.3mm shank diameter is common across compatible mounting plates. Check the hardware manufacturer's specification for the required screw diameter and length before substituting.
The nickel finish is primarily a cosmetic match for nickel-finished hardware. It does not change the thread engagement or holding strength in the panel material. These screws are for dry interior cabinet applications.
Each box contains 500 screws, which covers a full production run of hardware installation across multiple cabinets.
Matching screw length to panel depth and hardware plate geometry is what keeps European hardware sitting flat, functioning correctly, and looking finished inside the cabinet. The Grass 7.5mm nickel euro screw delivers that match for shallow-bore mounting positions, with a finish that disappears against nickel hardware rather than drawing the eye.
Sold In: 500 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 500 Each |  GF83000K Mfr# 83000-43 | Grass 6.3-18mm Flat Head Euro Screw Phillips Drive - Blunt Point Coarse Thread Nickel, 83000-43 - 500/Box | ||||
Sold in: 500 Each | GF81015K Mfr# 81015-43 | Grass 6.3-13mm Flat Head Euro Screw Phillips Drive - Blunt Point Coarse Thread Nickel, 81015-43 - 500/Box |