Brad point boring bit 3.2mm by Amana Tool

Brad Point Boring Bit 3.2mm For Clean Bores

Brad point boring bit 3.2mm describes a 3.2mm diameter brad point boring bit that centers quickly, helping drills start accurately when boring small, precise holes. The cutting edge brad point design forms a clean entry, which matters when working visible cabinet parts or jigs where tear-out affects fit. The bit has a 70mm cutting edge length, giving reach for deeper boring where a short flute might leave dust packed in the hole. This bit is built as a right hand cutting tool that rotates clockwise, so it matches standard clockwise-spindle boring machines and drill presses. It belongs to the boring bits category and the router bits product class, which positions it for fixed-machine drilling rather than handheld use. The manufacturer part number 204032 clearly identifies this exact Amana Tool pattern for repeat ordering across multiple jobs.

Key Boring Bit Details That Support Work

• The 3.2mm diameter brad point focuses cutting at the tip, which guides the bit into position so hole location stays consistent across line boring or repeated fence setups.
• The 70mm cutting edge length creates a long flute section that carries chips out of deeper holes, reducing heat buildup that can affect hole quality in production use.
• The right hand designation means clockwise rotation, aligning with standard machine spindles so operators can match rotation direction without changing existing motor setups.
• The 10mm shank size fits boring machines built for 10mm shank bits, so the bit seats securely in that style of collet or chuck for repeatable alignment.
• The Amana Tool brand association ties this bit to a known cutting-tool line, which helps shops match it with other Amana boring bits when standardizing tooling.

Installation And Machine Fit For This Boring Bit

This brad point boring bit is designed for boring machines that accept a 10mm shank, so it drops into those systems without shank adapters. The same bit can also be used in drill presses with a 3/8 inch shank interface, giving flexibility between dedicated boring equipment and general shop drill presses. The manufacturer states that it is not for portable drills or routers, which defines its role as a stationary-machine tool where the workpiece is supported and the spindle runs on fixed centers. As a right hand, clockwise-rotating bit, it aligns with typical spindle rotation, so operators keep standard motor wiring and controls while using this cutter.

Using This Brad Point Bit In Cabinet And Shop Work

Where This 3.2mm Boring Bit Is Applied

The 3.2mm x 70mm cutting edge brad point boring bit fits work where a small-diameter hole is needed along a consistent drilling pattern. In purpose-built boring machines with 10mm shank tooling, the shank matches the spindle sockets, so the bit sits true while boring cabinet parts or fixture components. In a drill press that accepts 3/8 inch shank tooling, the same design operates as a stationary drilling solution, supporting controlled feed and depth adjustments from the drill press table. The brad point geometry concentrates the initial cut at the center point, guiding the outer cutting edges as they follow, which supports straight bores when starting on layout marks or through pre-drilled pilot holes. As part of the boring bits family within the router bits product class, this cutter fits into shop workflows where parts are brought to the machine rather than driven by handheld tools.

Why These Boring Bit Details Matter In Use

The 3.2mm diameter sets a predictable hole size, so components depending on that bore can be designed around a consistent clearance or pilot dimension. The 70mm cutting edge length gives depth capacity, which matters when boring through thicker stock or when longer engagement is needed for specialty fixtures. Right hand, clockwise rotation syncs with most shop spindle directions, allowing the bit to cut correctly under existing machine settings. Limiting use to boring machines and drill presses, and not to portable drills or routers, keeps the bit operating in rigid setups where runout and side loading are better controlled by the machine structure. The 10mm shank aligns the cutter body relative to the spindle centerline, supporting accurate repeat bores across multiple parts. Identifying the bit by the Amana Tool name and part number 204032 helps shops reorder the exact same geometry, so replacement bits match earlier setups without changing programs, stops, or jigs.

Common Questions About This Amana Boring Bit

Select This Bit For Stationary Boring Accuracy

This 3.2mm x 70mm cutting edge brad point boring bit from Amana Tool combines a 3.2mm diameter, long cutting edge, and right hand clockwise rotation for controlled drilling on boring machines and drill presses. The 10mm shank configuration for boring machines and compatibility with 3/8 inch shank drill press setups place it squarely in stationary drilling workflows. For shops standardizing on a specific small-bore size with repeatable machine setups, choosing this 204032 bit aligns hole size, depth capacity, and spindle rotation with everyday cabinet and fixture boring tasks.