Amerock Conrad Cabinet Pull For Kitchen And Bath

Amerock Conrad cabinet pull gives a 3-3/4 in (96 mm) center-to-center grip that suits standard cabinet drilling, so installers can align handles quickly on doors and drawers. The pull uses zinc die-cast construction, which provides a solid-feeling handle that holds up during regular cabinet use in kitchens and baths. Its satin nickel finish offers a muted metallic look that works well in contemporary and transitional spaces, helping projects match popular appliance and fixture tones. The Conrad collection uses clean flowing lines with strong edges, so this pull reads modern while still pairing with simple shaker and slab fronts. Overall length of 6-1/16 in (154 mm) gives enough hand clearance across wider drawer faces, while the 7/16 in (11 mm) width keeps the profile slim for tight reveals. A 1 in (25 mm) projection spaces hands away from the door surface for comfortable gripping.

Key Conrad 96mm Pull Details For Projects

• The 3-3/4 in (96 mm) center-to-center dimension matches common cabinet boring patterns, allowing straightforward layout on new installations or straightforward replacement on existing fronts.
• The 6-1/16 in (154 mm) overall length stretches proportionally across typical drawer widths, helping lines stay consistent when pulls repeat across a run of cabinets.
• The 1 in (25 mm) projection sets the pull off the face just enough for fingers to wrap behind, which supports smooth opening on heavier doors and loaded drawers.
• The 7/16 in (11 mm) width keeps the pull visually light, which helps when spacing is tight between doors or near appliance panels in compact layouts.
• The satin nickel finish provides a soft metallic surface that coordinates with many hinges and faucets, supporting cohesive hardware specifications across a full room.
• The zinc die-cast material gives the pull a solid body, which helps it feel substantial when used repeatedly in busy kitchen and bath environments.

Amerock Conrad Pull Installation And Fit Details

The Amerock Conrad pull is built around a 3-3/4 in (96 mm) center-to-center mounting span, which aligns with standard cabinet drilling jigs during production or onsite work. With a 6-1/16 in (154 mm) overall length, this pull covers normal handle footprints, helping hide previous marks when replacing older hardware with the same center spacing. A projection of 1 in (25 mm) positions the gripping surface away from the cabinet face, which reduces knuckle contact against doors and drawer fronts during use. At 7/16 in (11 mm) width, the pull leaves clearance between adjacent doors where reveals are tight, beneficial on frameless cabinets or narrow faces. The satin nickel finish from Amerock Corporation supports a consistent look alongside other satin nickel components specified on the same project.

Using The Amerock BP29201G10 Pull In Real Projects

Where This Satin Nickel Conrad Pull Fits Best

The Amerock Conrad Series 3-3/4 in (96 mm) center-to-center satin nickel pull works well on kitchen and bath cabinetry where contemporary or transitional styling is desired. Its clean flowing lines with strong edges fit projects aiming for simple geometric hardware instead of ornate shapes. The 6-1/16 in (154 mm) overall length gives good proportion on standard base and wall cabinet doors, so one pull can typically run across most door sizes without looking undersized. Drawer faces benefit from the 96 mm center span because it sits in the common mid-range between small and oversized pulls, making layout consistent across stacked drawers. The 1 in (25 mm) projection also serves utility cabinets, where users often pull from the side angle and need a handhold set off the surface. For bath vanities using satin nickel faucets and fixtures, the satin nickel finish on this pull supports a unified hardware palette from doors to plumbing.

Details That Support Repeatable Hardware Results

The manufacturer part number BP29201G10 identifies this exact Amerock Conrad pull, which helps specifiers keep orders consistent across multiple rooms and phases of a project. The 3-3/4 in (96 mm) center-to-center spacing allows fabricators to standardize drilling templates, improving repeatability when boring dozens of fronts. With a 7/16 in (11 mm) width, this pull stays narrow enough that handles can be mirrored on pairs of doors without crowding, keeping sightlines straight along upper and lower runs. The zinc die-cast construction gives each pull a uniform form, so alignment of edges and faces remains consistent when lined up across large installations. The satin nickel finish is applied across the pull body, supporting a uniform appearance when several handles are mounted side by side under direct lighting. Using the Conrad collection design on both doors and drawers helps installers maintain one visual language throughout a job while varying only sizes or quantities as needed.

Common Questions About Amerock Conrad Cabinet Pulls

Select This Conrad Pull For Consistent Cabinet Runs

The Amerock Conrad Series 3-3/4 in (96 mm) center-to-center satin nickel pull BP29201G10 from Wurth Baer Supply combines zinc die-cast construction with a 6-1/16 in (154 mm) length and 1 in (25 mm) projection to support comfortable use. Its 7/16 in (11 mm) width and satin nickel finish help maintain clean, consistent lines across kitchen and bath cabinet runs. Use this pull when a single, modern profile is needed across doors and drawers while staying within standard drilling dimensions.