Metal Cabinet Fixed Height Aluminum, Style 8 Leg 6" Height

Metal Cabinet Fixed Height Aluminum Leg Use

Metal cabinet fixed height aluminum leg describes a 100% aluminum furniture leg from Peter Meier, Inc. that is built for cabinet and work surface support where a fixed 6 inch height is required. The stated 1-3/4 inch diameter spreads the load over a wider footprint, which helps support cabinets or tables steadily on typical interior floors. The 6 inch height establishes a comfortable working or toe-kick clearance zone, useful when setting up work surfaces or furniture with consistent elevation. The matte finish on the aluminum creates a subdued appearance, which helps these legs blend into modern cabinetry or shop fixtures without glare. Being in the Work Surface & Tables category with a Table Legs product class identifies it specifically for use under tables, cabinets, or furniture rather than as structural framing, helping installers quickly match it to the right job.

Key Furniture Leg Details For Installers

• The leg is made of 100% aluminum, which keeps weight down while still providing a rigid support component for cabinets and tables over long spans.
• The 1-3/4 inch diameter creates a sizable bearing surface at the floor, helping distribute loads to reduce point pressure on finished flooring during everyday use.
• The leg height of 6 inches sets a fixed elevation for cabinets or work surfaces, supporting uniform layouts when multiple legs are used on a run of furniture.
• Style 8 features a built in 1 inch adjustable foot, allowing small height changes at the floor so installers can compensate for minor floor unevenness.
• The bottom of the leg has an attached thick felt pad, which cushions contact with the floor and helps protect finished flooring when furniture is positioned or shifted.
• Two available heights, 4 inch and 6 inch, give designers and installers flexibility to match furniture or cabinet height requirements in a project line.

Mounting And M10 Thread Installation Details

The Peter Meier, Inc. metal cabinet fixed height aluminum leg can be mounted via an M10 thread screw, tying the leg directly into an M10 threaded connection on the furniture bottom. This threaded interface supports positive, repeatable installation when cabinets or tops are prepped with M10 inserts. The same leg can also be mounted using the mounting plate, giving installers a flat-interface option when a simple surface attachment is preferred. This dual mounting option lets fabricators choose between threaded and plate mounting depending on their shop tooling and cabinet construction methods, which supports consistent results across different projects.

How This 6 Inch Style 8 Leg Works

Where This Aluminum Table Leg Fits Best

This metal cabinet fixed height aluminum, Style 8 leg is positioned by Wurth Baer Supply in the Work Surface & Tables category, directing it toward cabinets, furniture, and tables needing a 6 inch support. The 6 inch leg height suits work surfaces or cabinets that must clear floor transitions while staying within standard furniture proportions. The 1-3/4 inch diameter helps it sit solidly under bases, which is important when supporting tops in kitchens, shops, or office furniture where stability is a priority. Being a furniture leg with a matte finish helps it visually coordinate with contemporary casework or metal-framed pieces, so the support element works with the overall design instead of drawing attention. Because the leg is 100% aluminum, it is appropriate for indoor woodworking and furniture environments where a metal support component is beneficial.

Details That Support Leveling And Consistency

Style 8 on this leg features a built in 1 inch adjustable foot, which provides fine-tuning capability around the nominal 6 inch height to help align cabinet runs or work surfaces when floors are slightly out of level. That 1 inch of adjustment range allows installers to dial in final pitches without altering the fixed-leg body, protecting design lines while correcting height. The attached thick felt pad at the bottom adds a protective layer between the adjustable foot and the floor, which helps reduce marking and scuffing when cabinets or furniture are positioned or shifted during layout. Mounting via an M10 thread screw supports a solid mechanical connection, helping keep legs square to the cabinet bottom for predictable adjustment at the foot. Using the mounting plate option, as described in the web description, gives shops a standardized footprint when building cabinets without threaded inserts, which supports repeatable assembly in production runs. The combination of aluminum construction, adjustable foot, and thick felt pad means these legs serve both structural support and finished-floor friendliness in everyday cabinet and table installations.

Common Questions About This Aluminum Furniture Leg

Selecting This 6 Inch Aluminum Leg For Work

This Peter Meier, Inc. metal cabinet fixed height aluminum, Style 8 leg with 6 inch height, 1-3/4 inch diameter, and matte finish provides a defined support solution for cabinets and work surfaces. The M10 thread or mounting plate options, combined with the built in 1 inch adjustable foot and attached thick felt pad, give installers practical control over leveling and floor contact. For projects sourced through Wurth Baer Supply that call for a 6 inch aluminum furniture leg in this configuration, choosing this model keeps height, adjustment, and finish aligned with the specified design.