Liberty Hardware Southampton Pull 3" (76 mm) Center to Center, Satin Nickel, P20385-SN-C

Liberty Southampton Cabinet Pull For 3 Inch Layouts

Liberty Southampton cabinet pull is a 3 inch center to center handle that sets up consistent hole spacing for cabinet doors or drawers, which helps keep layouts uniform across a run. The pull is part of the Liberty Hardware Southampton collection, so its profile and detailing match that series for cohesive projects. Its zinc die cast material creates a solid, rigid pull body, which supports everyday opening and closing forces on frequently used cabinets. The satin nickel finish provides a muted, brushed look, which works well where a softer metallic appearance is preferred. Overall length of 4-1/4 inches gives finger clearance beyond the 3 inch mounting centers, which helps users grip comfortably. A 1 inch projection sets the pull off the face just enough for fingers to wrap behind, while keeping the handle close to the panel for a tidy look and reduced snagging.

Key Liberty P20385-SN-C Pull Details In Use

• The 3 inch center to center dimension defines the drilling layout, which simplifies planning when aligning multiple pulls across cabinet faces.
• The 4-1/4 inch overall length extends past the mounting points, which gives users extra edge to grab without crowding adjacent hardware.
• The 1 inch projection sets a predictable stand-off from the door, which balances finger clearance with a low profile along the cabinet run.
• The 11/16 inch width provides a narrow grip area, which works well on smaller drawer fronts or doors where wider bars might look oversized.
• The zinc die cast construction forms a rigid one-piece body, which supports repeated pulling forces on busy kitchen or shop cabinets.
• The satin nickel finish delivers a soft metallic tone, which coordinates with other satin nickel fixtures for a consistent appearance.

Installation Layout And Fit For This Cabinet Pull

The 3 inch center to center mounting of this satin nickel pull sets the exact spacing for two holes, which streamlines drilling jigs and templates on new cabinet builds or refacing jobs. With an overall 4-1/4 inch length, the pull positions its mounting points slightly inboard from the ends, which helps keep screw locations clear of door edge details or narrow rail sections. The 1 inch projection defines how far the handle sits off the surface, which makes it easier to plan for door overlap and neighboring hardware clearances. At 11/16 inch width, the pull occupies a compact band on the face, which is practical when laying out multiple handles on small fronts or tight vertical stacks.

Using This Satin Nickel Pull In Cabinet Projects

Where The Liberty 3 Inch Pull Fits Best

This Liberty Hardware pull belongs to the Southampton collection, which positions it for projects using that specific series across a kitchen, bath, or built-in. Its 3 inch center to center dimension matches common cabinet drilling patterns, which makes it a straightforward choice when layouts are based on that spacing. The satin nickel finish suits environments that already feature satin nickel hinges, faucets, or lighting, which keeps visible hardware finishes aligned. With 4-1/4 inch overall length, the pull scales well on small to medium cabinet doors and drawers, which helps maintain proportion on standard residential fronts. The 11/16 inch width keeps the handle visually light, which is useful on narrow rails or slim drawer faces where bulkier pulls might dominate the panel.

Details That Support Consistent Cabinet Results

The 3 inch center to center measurement on the P20385-SN-C pull provides a repeatable drilling reference, which helps installers maintain straight lines of hardware across long runs. Its 1 inch projection creates predictable clearance for fingers behind the bar, which aids users who prefer a defined gap without the handle standing too far off the cabinet face. The zinc die cast material gives the pull a solid, integrated form, which supports smooth operation over repeated use in kitchens, workrooms, or storage areas. The satin nickel finish offers a consistent surface tone, which supports a uniform look when multiple pulls are mounted side by side. With its defined length, width, and projection, the pull provides fixed dimensions that simplify layout drawings and job planning for repetitive cabinet work.

Common Questions About Liberty P20385-SN-C Pull

Selecting This Pull For Satin Nickel Cabinet Runs

This Liberty Southampton cabinet pull combines 3 inch center to center mounting, 4-1/4 inch overall length, and 1 inch projection, which suits many standard cabinet layouts. The zinc die cast construction and satin nickel finish align with projects using Liberty Hardware Southampton collection pieces. For runs built around satin nickel tones and 3 inch drilling patterns, this P20385-SN-C pull offers a defined set of dimensions that support consistent cabinet hardware results.