Tiomos Adjustment Wing Mounting Plate For Precise Hinges

Tiomos adjustment wing mounting plate describes a Grass America hinge mounting plate designed as a hinge mounting plates component for cabinet work requiring repeatable adjustment. The 0mm wing mounting plate design sets the mounting height at zero millimeters, which helps keep door and frame alignment tied directly to the hinge geometry when laying out new installations or matching existing runs. The plate is part of the Tiomos adjustment system, so it serves as the base element that connects hinge and cabinet while allowing later fine-tuning. As a steel hinge base plate, it supports the hinge arm with a rigid interface, which matters when doors are used frequently. The manufacturer part number F058139761228 uniquely identifies this specific combination of wing format, 0mm height, and adjustment style for reorder or matching on multi-cabinet projects.

Key Mounting Plate Details For Daily Work

• The 4 point fixing layout secures the hinge mounting plates to the cabinet with four anchoring points, which spreads load and helps doors track consistently over time in regular use.
• Height adjustment via worm gear provides controlled, incremental movement of the door position, so installers can dial in reveals without loosening and re-setting the entire hinge arm.
• The steel, nickel-plated construction pairs a rigid steel core with a nickel surface, supporting hinge loads while presenting a metal finish suited to typical cabinet interiors.
• The screw-on mounting style lets the hinge mounting plates attach using screws through the 4 point fixing pattern, integrating into standard cabinet construction routines.
• Pre-mounted euro screws described in the product data position the fixing in the plate design, aligning with European-style cabinet drilling patterns in shop or onsite workflows.

Screw-On Wing Plate Setup And Adjustment

This screw on hinge mounting plate uses 4 point fixing to tie the hinge mounting plates firmly to the cabinet side, so layout depends on consistent screw positioning rather than complex hardware. The 0mm wing mounting plate height keeps the reference plane at cabinet surface level, so hinge geometry sets the door overlay instead of an offset plate thickness. Height adjustment via worm gear then refines the door position along the vertical axis, allowing the installer to move the door in small steps by turning the mechanism rather than shifting the plate body. With steel, nickel-plated construction, the plate holds its position under the clamping force of the screws during these adjustments, which supports stable alignment after the final setting.

Using This Hinge Mounting Plate In Projects

Where This Grass America Plate Fits Best

This Tiomos adjustment wing mounting plate functions as a hinge mounting plates base in cabinet and casework constructions using matching Tiomos hinges from Grass America. The 0mm wing mounting plate configuration suits layouts where the cabinet side or mounting surface is the primary reference plane, so hinge geometry controls overlay and gap. In cabinet runs that rely on consistent reveals, the 4 point fixing pattern anchors the plate at four locations, so each door uses the same mounting geometry across the project. The screw-on installation suits wood-based cabinet materials that accept screws, integrating with common shop drilling and assembly steps. Because the product is a steel hinge base plate with nickel plating, it works within typical cabinet interiors where exposed hardware visibility and metal-to-wood contact are both common.

Adjustment And Repeatable Alignment Advantages

The height adjustment via worm gear allows the installer to shift door position vertically while the plate stays fastened through its 4 point fixing pattern, which reduces the need to re-position screw holes during fine-tuning. This adjustment method operates through a geared mechanism, so turning the adjuster translates into controlled movement rather than sliding the hinge by hand, giving more predictable changes to the reveal. Using a 0mm wing mounting plate keeps the adjustment centered around the cabinet surface, simplifying measurement when repeating settings across multiple openings. The steel, nickel-plated body resists deformation under screw pressure, supporting the worm gear mechanism as it carries door loads after final alignment. With the fixed geometry of the wing format and the F058139761228 part reference, installers can replicate an established setup on future work by ordering the same hinge mounting plates.

Common Questions About F058139761228 Plate

Selecting This Mounting Plate For Your Hinges

The Tiomos adjustment wing mounting plate combines 4 point fixing, a 0mm wing mounting plate height, and height adjustment via worm gear in a single hinge mounting plates component. For cabinet projects using Tiomos hinges from Grass America, this steel, nickel-plated base plate gives a defined mounting plane with built-in vertical adjustment. When a project calls for repeating a proven hinge setup or matching an existing Tiomos installation, the F058139761228 identifier connects directly to this exact configuration. Wurth Baer Supply lists this plate for professional woodworking and cabinet applications, so it can be specified wherever controlled adjustment and repeatable hinge geometry are important requirements.