Tiomos Adjustment Wing Mounting Plate For Precise Hinges

Tiomos adjustment wing mounting plate describes a Grass America hinge mounting plate designed to support Tiomos hinge installations where consistent overlay and alignment matter. The plate is a hinge mounting plate in steel, so it provides a solid base for the hinge arm in cabinet applications. The 2mm wing mounting plate height positions the hinge arm at a defined level, helping keep door reveals consistent across a run. The plate is nickel-plated, which adds a hard surface over the steel, useful in typical shop or jobsite environments where parts contact tools and fasteners during installation. The design is classed as a hinge mounting plate, so it functions as the interface between the cabinet and the Tiomos hinge arm, tying your layout back to a known, repeatable reference.

Key Mounting Plate Details For Daily Work

• The mounting plate uses 4 point fixing, so the plate is secured at four locations, helping resist movement when doors are operated repeatedly in cabinet use.
• Height adjustment via worm gear lets you adjust door position through the plate mechanism, supporting controlled vertical tweaks without shifting the cabinet layout.
• The part is made from steel, so the base resists bending loads from door motion, supporting alignment when heavier fronts are opened and closed in normal service.
• The nickel-plated surface over the steel resists wear from tools and hinge engagement, which helps maintain smooth adjustment action at the fixing points over time.
• Pre-mounted Euro screws in the plate give a defined fixing interface, so the fasteners are ready to drive into the matching system for consistent clamping.

Mounting And Adjustment Details For Installation

This Grass America hinge mounting plate is a screw-on style, so it is secured using screws rather than press-in fittings, giving a solid mechanical connection to the cabinet structure. The 4-point fixing layout spreads load across four screw positions, which supports stable seating on the mounting surface during hinge adjustment work. Height adjustment via worm gear is built into the plate, so vertical door position is tuned through the gear movement instead of loosening multiple screws, reducing disturbance to the base location. The 2mm plate height defines the starting offset for the Tiomos hinge arm, which helps keep overlay calculations predictable from cabinet to cabinet. The use of steel with a nickel-plated finish provides a robust, hard-wearing interface where the hinge arm locks down and where adjustment forces are applied.

How This Mounting Plate Functions In Use

Where The 2mm Wing Mounting Plate Fits

This Tiomos adjustment wing mounting plate from Grass America sits between the cabinet and the hinge arm as part of a hinge assembly, so it carries the operational load when doors swing. The 2mm mounting plate height sets the basic geometry for the hinge position, supporting layouts where consistent overlay is required along a bank of doors. Because the plate is a wing style, the form reaches out from the fixing area, giving a defined footprint for the 4 point fixing pattern on the cabinet surface. The screw-on design with pre-mounted Euro screws means the interface uses screws as the primary connection to the compatible system, giving an installed plate that is firmly drawn against the mounting surface. Made from steel and nickel-plated, the plate gives a rigid base for the hinge arm clamp, which supports repeatability when multiple doors share the same hinge series on a project.

Why Worm Gear Height Adjustment Supports Results

The height adjustment via worm gear built into this hinge mounting plate allows vertical door alignment changes to be made in a controlled manner at the plate. Turning the worm gear shifts the effective plate position relative to the hinge arm, so door gaps can be fine-tuned after the cabinet has been fixed in place. Because the plate uses 4 point fixing, these adjustments act on a stable base that resists tilting as the gear is moved, supporting accurate parallel reveals along the cabinet front. The 2mm wing mounting plate height works together with the worm gear system, giving a known baseline for overlay calculations and allowing installers to repeat settings across multiple cabinets. With the steel construction and nickel-plated surface, the gear and bearing areas experience metal-to-metal contact on durable surfaces, which supports smooth, repeatable adjustments during both initial setup and later alignment work.

Common Questions About This Grass Mounting Plate

Select This Plate For Controlled Hinge Alignment

The Grass America Tiomos adjustment wing mounting plate with 4 point fixing, steel construction, and nickel-plated finish gives a defined 2mm mounting height and worm gear height adjustment for precise door positioning. With pre-mounted Euro screws and a screw-on connection style, it ties the hinge arm back to a stable, repeatable base. For projects that rely on the Tiomos system and demand consistent reveals across multiple fronts, this F058139762228 mounting plate offers a clearly specified foundation that supports reliable cabinet hinge alignment.