Tiomos Wing Base Plate For Frameless Cabinets

Tiomos cam adjustable frameless wing base plate gives a Grass America Tiomos hinge a dedicated mounting point on a frameless cabinet side, so the hinge can carry the load where you need it without improvising a mounting surface.

This 3mm wing plate sets the door position by fixing the hinge height relative to the cabinet, which matters when you are matching reveals across a run of doors or lining up with existing casework.

The plate is built from steel and nickel-plated, so the hinge connection has a solid metal interface that resists wear at the screw and cam areas during repeated adjustments.

Because this part is a hinge mounting plate in the Hinges|Hinge Base Plates category, it serves as the transition between the cabinet side and the Tiomos hinge, saving layout time compared with building up custom blocking.

The design is intended for a frameless application, so it suits cabinet construction that relies on the side panel as the main mounting surface rather than using a face frame.

Key Wing Plate Details That Support Hinge Setup

• The 3mm wing plate thickness establishes a consistent offset between the hinge and cabinet side, which is important when you want the same gap and overlay repeated from cabinet to cabinet.
• The 4 point fixing layout secures the plate at four positions on the cabinet, spreading load into the side panel so door weight and closing forces are carried by multiple fasteners instead of just two.
• Height adjustment via worm gear builds a fine-adjustment mechanism into the plate, allowing precise vertical tuning of the door position so reveals line up after the case is installed.
• The twin application design supports using the plate in paired setups, which matters when you are standardizing hardware across symmetrical door or panel configurations.
• Steel, nickel-plated construction provides a rigid base and a plated surface at the hinge interface, which helps the mounting points stay stable through door cycles and adjustment tweaks.
• Pre-mounted Euro screws on the plate give you a ready-to-use connection at the hinge interface, so attaching the hinge body to the plate is faster and more repeatable on repetitive jobs.

Frameless Hinge Plate Mounting And Adjustment Workflow

This hinge mounting plate uses 4 point fixing to anchor into the cabinet, so once the holes are drilled on layout, the plate locates itself squarely and resists twist when the hinge is loaded.

The worm gear height adjustment built into the plate allows vertical movement without loosening the primary fixing points, which keeps the plate solid while you fine-tune the door alignment.

Because the plate is a 3mm wing style for frameless cabinets, it positions the hinge cup in a predictable relationship to the cabinet edge, simplifying drilling patterns and door boring layouts.

The Euro screws are pre-mounted in the plate threads for the hinge connection, so you bring the Tiomos hinge body to the plate and secure it using the existing screw locations set at the factory.

Using The Tiomos Wing Plate In Cabinet Runs

Where This 3mm Tiomos Wing Plate Fits Best

This Tiomos cam adjustable frameless wing base plate is intended for frameless cabinet construction where the cabinet side panel is the main structural mounting surface for the hinge assembly.

The 3mm wing plate height defines the hinge stand-off from the panel, so in cabinet runs where multiple doors share a common top or bottom line, you gain a repeatable base dimension from the case edge.

Because it is a hinge mounting plate in the Grass America Tiomos system, it suits situations where you are using Tiomos hinges and want their motion to originate from a rigid, standardized mounting point.

The twin application capability gives you flexibility in layouts that use pairs of hinges with mirrored positions, supporting consistent geometry across left and right doors in the same bank.

In commercial or shop-built cabinet work, the combination of wing shape and 4 point fixing makes this plate well suited to particleboard or similar sheet goods, where spreading load over more fasteners helps the hinge perform over time.

How Worm Gear And 4 Point Fixing Improve Results

The 4 point fixing arrangement ties the plate to the cabinet with four fastener points, which stabilizes the hinge base and reduces the chance of the plate shifting when doors are cycled repeatedly.

This fixing pattern also supports accurate installation jigs, since the hole pattern can be repeated along a cabinet run so every hinge starts from the same reference geometry.

Height adjustment via worm gear places the vertical tuning right in the plate, giving you controlled, incremental movement that lets you correct for small variations in cabinet squareness or door size without re-drilling.

The worm gear mechanism keeps its position once set because it is built into the plate body, so alignments you dial in at installation are maintained when doors are opened and closed.

Steel, nickel-plated construction around the worm gear and hinge interface gives the moving and bearing surfaces a robust metal contact area, supporting smooth adjustment even after multiple service visits.

Pre-mounted Euro screws tie directly into the hinge attachment, so when you bring the Tiomos hinge onto the plate, the alignment between cam adjustment in the hinge and worm gear in the plate is preserved from one cabinet to the next.

Common Questions About This Grass Tiomos Base Plate

Selecting This Tiomos Plate For Your Next Build

This Tiomos cam adjustable frameless wing base plate from Grass America combines a 3mm wing height, 4 point fixing, and worm gear height adjustment, giving you a consistent hinge base when building or outfitting frameless cabinets.

With steel, nickel-plated construction and pre-mounted Euro screws, the plate provides a prepared mounting interface for Tiomos hinges, supporting accurate door positioning in shop-built runs or on-site cabinet work where repeatable hardware geometry matters.