
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Candler pull 128mm center to center defines this Amerock Corporation handle as a 5-1/16 in (128 mm) center-to-center pull that sets accurate drilling layout for cabinet doors and drawers. The broad-faced design described in the Candler collection spreads hand contact over a wider surface, which helps reduce localized wear points on finished fronts. Traditional feet at each end give the pull a stable stance on the mounting surface, which supports consistent alignment across multiple fronts on the same run. The gunmetal finish called out in the description provides a dark, uniform appearance that coordinates with other gunmetal components on the project. Constructed from zinc, this pull offers a solid-feeling grip while keeping weight manageable on lighter cabinet faces. Overall length of 6-9/16 in gives good hand clearance across standard cabinet widths, while the 1-1/4 in projection sets the handle off the face enough for a comfortable grasp in daily use.
The specified 5-1/16 in (128 mm) center-to-center dimension gives a precise drilling distance that guides jig setup and repeatable boring from front to front. The stated 6-9/16 in overall length defines the footprint on the cabinet, which helps with proportion decisions on narrow versus wide doors. A 1-1/4 in projection keeps the pull comfortably off the face, which provides finger clearance while still keeping the handle tight to the cabinet line. The 13/16 in width concentrates the broad-faced design into a controlled band across the front, which balances visual weight with rail sizes on typical cabinet constructions. The listed screw size of #8-32 x 1 in truss head machine screw describes the threaded interface, which matches common cabinet boring for pulls of this type.
The Amerock Candler series label places this pull in a decorative hardware and moldings category, aligning it with typical cabinet doors and drawers in residential or commercial woodworking. The 5-1/16 in (128 mm) center-to-center dimension suits standard drilling patterns used on many face-frame and frameless cabinet layouts, helping one pull model serve across multiple box sizes. Its gunmetal finish allows this handle to coordinate with other gunmetal decorative components on the same job, supporting a unified finish story across hinges, pulls, and other visible hardware. The broad-faced design described for the Candler collection provides a substantial look that suits medium to larger cabinet faces, giving enough visual presence so hardware does not disappear on taller doors or wide drawers. Traditional feet at each end introduce a structured base detail, which fits well with doors that have framed or profiled rails and stiles.
The defined 5-1/16 in (128 mm) center-to-center drilling distance gives installers a single measurement to repeat with jigs or templates, which supports straight pull lines across long cabinet runs. The 6-9/16 in overall length anchors that drilling dimension visually, keeping screw holes positioned within a handle size that looks balanced on typical cabinet widths. A projection of 1-1/4 in brings the pull far enough off the face for fingers to hook behind, which can ease operation on heavier or loaded drawers. The 13/16 in width focuses the broad-faced concept into a consistent band, which helps align the pull with center rails or design lines on the door fronts. Construction in zinc provides a solid-feeling part that still remains workable for installers during alignment and snugging, supporting precise final positioning without excessive weight stressing the front panel.
The Amerock Candler pull uses a 5-1/16 in (128 mm) center-to-center hole spacing, which sets the drilling layout for doors and drawers using this handle.
The Amerock BP29363GM pull has a length of 6-9/16 in and a width of 13/16 in, defining its footprint on the cabinet face for proportion planning.
This gunmetal cabinet pull has a projection of 1-1/4 in, setting how far it stands off the cabinet surface for finger clearance.
The Candler collection pull is made from zinc, providing a solid feel while keeping weight appropriate for typical cabinet doors and drawers.
This Amerock Candler pull is specified in a gunmetal finish, giving a dark, consistent appearance that coordinates with other gunmetal hardware.
The Amerock Candler pull uses #8-32 x 1 in truss head machine screws, aligning with common threaded holes used in cabinet pull installations.
The Amerock Candler series 5-1/16 in (128 mm) center-to-center gunmetal pull combines a broad-faced design, traditional feet, and a defined 6-9/16 in length to give cabinets a structured, consistent look. The zinc construction and 1-1/4 in projection support a comfortable, solid grip on everyday doors and drawers. With the specified 5-1/16 in (128 mm) center-to-center dimension and #8-32 x 1 in truss head machine screw interface, this pull aligns with standard cabinet drilling and threading practices. For projects built around the Candler collection and gunmetal finish, this handle offers a clear, documented size and style choice.
Sold In: 1 Each