Hickory Hardware free swinging inset non-mortise hinge gives you a semi-concealed, screw-on solution for inset doors where you want a traditional hinge look without cutting a mortise. This P8294-SN model from Belwith Keeler uses steel construction, so the hinge body stands up to regular cabinet and furniture door use in a shop or residential setting. The fast pin design lets the leaves pivot smoothly around a fixed pin, which helps doors swing freely without binding when the frame and door are aligned properly. Sized at 2 inches long by 1-7/16 inches wide, this hinge offers a compact footprint that suits smaller cabinet doors, face-frames, or light-duty furniture applications where a full-size butt hinge would be oversized. The satin nickel finish provides a clean, modern look that coordinates with many pulls and knobs in similar finishes across a project.
This semi-concealed face-frame hinge uses a non-mortise design, so the leaves sit directly on the door and frame surfaces, which avoids cutting recesses in the wood. The screw-on style means the hinge attaches using standard screw holes in the leaves, giving installers a familiar approach when laying out and driving fasteners into the frame and door edge. Because the hinge is classified as an inset non-mortise hinge, it is intended for doors that sit within the cabinet opening rather than overlaying the frame, so the knuckle projects at the edge while most of the leaves remain discreet. With a steel body and a compact 2 inch by 1-7/16 inch size, the hinge supports typical cabinet and light furniture doors where a semi-concealed appearance is part of the design.
This semi-concealed hinge belongs in the non-mortise hinge category and is listed specifically for face-frame work, so it suits cabinets or furniture with a frame around the opening. As an inset non-mortise hinge, it is intended for doors that close flush inside that frame, leaving the knuckle and finial tip visible at the edge while most of the hardware stays out of sight. The 2 inch length and 1-7/16 inch width keep the leaves compact enough for typical kitchen, bath, or built-in storage doors where stile widths are limited. With steel construction, the hinge offers a solid feel when mounted to wood doors and frames, supporting repeated use in cabinetry where opening and closing cycles are frequent.
The non-mortise design means the door and frame edges remain intact, so layout focuses on face positioning rather than cutting recess depths, which simplifies repeating the same setup across multiple cabinet openings. Because this is a free swinging hinge with a fast pin, the movement centers on a fixed pivot point, so each door swings through the same arc when hinges are set consistently along the edge. The semi-concealed form hides much of the leaf while still presenting a traditional hinge knuckle, which helps projects achieve a classic cabinet look without complex joinery. The satin nickel finish creates a neutral metallic tone that pairs effectively with many modern and transitional knob and pull styles, helping projects maintain a coordinated appearance from hinge to handle. Using a known Belwith Keeler part number, P8294-SN, also helps maintain consistency when reordering hinges for additional cabinets or for future matching work on the same job.
The P8294-SN model is a Hickory Hardware free swinging inset non-mortise finial tip hinge, so it is designed for inset cabinet doors using a non-mortise, semi-concealed layout.
This hinge is a screw-on non-mortise design, so it mounts directly to the door and face-frame surfaces using screw holes in the steel leaves.
This non-mortise hinge measures 2 inches long by 1-7/16 inches wide, so it suits many cabinet and light furniture doors with limited stile width.
The P8294-SN hinge uses steel construction, giving the hinge body rigidity for supporting cabinet door movement under normal use.
The satin nickel finish provides a muted metallic look that coordinates with satin nickel pulls and knobs, helping projects maintain a consistent hardware appearance.
The free swinging fast pin design means the door pivots around a fixed pin, providing smooth movement when the hinge is aligned on the cabinet door and face-frame.
The Hickory Hardware free swinging inset non-mortise hinge in satin nickel brings semi-concealed styling, steel construction, and a compact 2 inch by 1-7/16 inch footprint to cabinet and furniture work. When a project calls for inset, face-frame doors with visible knuckles that coordinate with satin nickel pulls and knobs, this P8294-SN hinge from Belwith Keeler offers a straightforward, screw-on option using a familiar non-mortise layout. For runs of cabinets or built-ins using the same hinge style, the consistent dimensions and part number support repeatable results across the entire installation.