Self mortise hinge 2-1/2 l x 1-1/2 w sn describes a Hickory Hardware Free Swinging Inset Non-Mortise Finial Tip Hinge that supports inset cabinet doors without cutting a mortise, so door and frame preparation stays simple on face-frame work. The hinge belongs to the Semi-Concealed Hinges product class, so part of the hardware sits inside the cabinet while the decorative finial tip shows, giving cabinets a finished look while keeping most of the hinge out of sight. The hinge size of 2-1/2 inches long by 1-1/2 inches wide sets the footprint on the frame and door edge, which helps installers plan layout and spacing on small to medium cabinet doors. The satin nickel finish matches the SN designation, so the hinge coordinates with other satin nickel cabinet hardware when building or updating a run of cabinets.
The product name states this is a non-mortise hinge, which allows mounting directly to the cabinet frame and door edge without cutting recesses, saving time on installations where speed and repeatability matter. The description notes a screw-on satin nickel design, so attachment relies on standard screw fastening, giving installers a familiar approach when hanging inset doors on face frames. The center hole frame wing feature described for locking in after height is adjusted supports step-by-step alignment, where the hinge can be loosely fitted, height set, then locked to preserve that setting during the rest of the installation. The 2-1/2 inch length and 1-1/2 inch width from the SAP description define a compact mounting footprint, which helps this hinge fit typical cabinet stile widths without crowding adjacent hardware or door edges.
The Hickory Hardware Free Swinging Inset Non-Mortise Finial Tip Hinge is identified as a Semi-Concealed Face-Frame Hinge, so it is intended for cabinet installations that use a face frame with inset doors where the door sits flush with the frame. The semi-concealed hinge design places part of the leaf inside the opening while leaving a visible portion with the finial tip, which suits projects where hardware should add a small decorative detail without dominating the cabinet front. The satin nickel finish, called out both in the product name and as SN in the SAP description, helps this hinge visually coordinate with satin nickel pulls and knobs on the same cabinet bank, so hardware across doors and drawers looks consistent. The 2-1/2 inch long by 1-1/2 inch wide sizing from the SAP description supports use on typical cabinet doors where a compact hinge plate is preferred, allowing placement on narrow face-frame members while still providing enough bearing surface for screw-on mounting. Because the hinge is described as free swinging, door movement follows the user pull without spring resistance, which can help doors open smoothly when matched with catches or latches selected for the cabinet design.
The center hole frame wing for locking in after height is adjusted gives installers a clear reference point when setting the door vertically, because that specific hole can be used to secure the final height after test fitting. This center reference helps keep multiple doors aligned along a run of cabinets, as installers can repeat the same sequence of loose fit, adjust, and lock using the same hinge feature on every opening. The non-mortise construction stated in the product name reduces layout steps, since hinge position depends on surface placement rather than mortise depth, which can simplify consistent results when several doors share the same gap and reveal targets. The fast pin size, mentioned alongside the overall hinge dimensions, supports uniform pivot behavior across hinges of this model, which matters when matching reveals at the hinge side so doors clear the frame while still appearing even. The finial tip described in the product name also helps visually confirm hinge alignment from the front, since misalignment at the tip would show against the satin nickel finish, encouraging careful hinge placement during installation passes.
The P8293-SN model is a Hickory Hardware Free Swinging Inset Non-Mortise Finial Tip Hinge in the Semi-Concealed Hinges product class, so it serves inset cabinet doors on face-frame cabinetry.
The self mortise hinge has a size of 2-1/2 inches long by 1-1/2 inches wide, giving a compact footprint suitable for typical cabinet door and face-frame mounting areas.
The center hole frame wing for locking in after height is adjusted allows the hinge to be set at the desired door height, then secured so that vertical alignment remains consistent across openings.
The non-mortise design means the hinge mounts on the surface of the frame and door without cutouts, which streamlines preparation and supports faster, repeatable cabinet door installations.
The hinge is described as satin nickel and carries the SN designation, so its surface appearance matches other satin nickel cabinet hardware used on the same installation.
The free swinging action in the product name indicates the hinge moves without built-in closing force, so doors open and close according to pulls and catches chosen for the cabinet.
The Hickory Hardware Free Swinging Inset Non-Mortise Finial Tip Hinge, in satin nickel and sized at 2-1/2 inches long by 1-1/2 inches wide, offers a semi-concealed option for inset face-frame cabinet doors where a compact, decorative hinge is required. The center hole frame wing for locking in after height is adjusted supports precise alignment during installation passes, while the non-mortise, screw-on design suits workflows focused on consistent, efficient door hanging. For projects matching satin nickel hardware and using semi-concealed hinges, this P8293-SN hinge provides a defined size, finish, and mounting style to build into layout and door planning.