Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Bed storage lift mechanism gas spring assisted hardware from Selby Furniture Hardware supports a bed platform with gas spring power so the platform can raise for access and lower in a controlled way on storage projects. The 48 inch length of this lift mechanism gives generous support along the bed platform, which helps distribute the load when the platform is opened. The 209 lbs per pair target weight rating refers to the combined weight of platform, mattress, and bedding that the pair of mechanisms is designed to balance, which guides material choice and bed size planning. Twin gas pistons on each mechanism assist the lifting motion, so the platform opens easier under load. Those same gas pistons also temper the closing motion for a safer close, which is important when the platform is heavier. The design is intended for use without a box spring, so the mattress sits directly on the platform structure.
This Selby bed storage lift mechanism is specified for bed frames built from material that equals or exceeds 3/4 inch hardwood plywood or 4/4 hardwood lumber, which sets a stiffness baseline for the load path between the lift hardware and the storage frame. That material requirement means the installer plans for substantial side rails and platform framing so the gas spring forces are carried without excessive flex. The mechanism is designed to operate with a standard innerspring or foam mattress between 6 and 10 inches thick, which affects the final center of gravity as the platform pivots. Operation without a box spring places the mattress directly on the platform, so the lift brackets interface with a single structural deck and the lift motion reflects only that defined mass.
This 48 inch bed storage lift hardware from Selby Furniture Hardware is intended as builders hardware for bed projects where access to storage under a platform is part of the design. The gas spring assisted mechanism can be oriented to open from the side of the bed, which works where there is clear lateral space along the rail. The same mechanism can also be oriented to open from the end of the bed, which suits layouts where foot-end access is more practical than side access. With a target weight of 209 lbs per pair, the mechanism is matched to a combined platform, mattress, and bedding mass in that range, aligning with many standard bed builds that aim for consistent lift behavior. Using 6 to 10 inch thick standard innerspring or foam mattresses keeps the operating weight within the window that the gas pistons are tuned to support. The product sits in the bed hardware class, so it is aimed at projects where the bed frame itself provides the structure for the lifting platform.
The twin gas pistons on each gas spring assisted mechanism share the lifting load across two cylinders, which smooths the lift curve and reduces high-spot effort as the platform moves through its arc. This twin-piston arrangement contributes to a safer close because the gas springs resist sudden dropping as the user guides the platform down. Orientation flexibility between side and end opening lets the installer keep piston geometry similar while adapting to room layout, which supports repeatable performance across different bed designs. The requirement that frame material equals or exceeds 3/4 inch hardwood plywood or 4/4 hardwood lumber anchors the mounting to robust framing, which helps the gas springs hold alignment over time. Operating without a box spring holds the moving mass to the platform, mattress, and bedding, so the 209 lbs per pair target weight can be used directly when estimating performance. The fully assembled one-piece unit configuration per side means alignment between gas pistons and pivot elements is factory set, which reduces variables during installation and helps each build behave consistently.
The 209 lbs per pair target weight describes the combined weight of platform, mattress, and bedding that the pair of mechanisms is designed around, guiding material choices so lifting and closing stay balanced.
This bed storage lift mechanism can be oriented to open from the side or from the end of the bed, allowing the opening direction to match room layout and access preferences.
The 6 to 10 inch standard innerspring or foam mattress range aligns with the gas spring assist, so the lift and close actions stay within the performance range the pistons are tuned for.
This lift hardware is specified for bed frames built from material that equals or exceeds 3/4 inch hardwood plywood or 4/4 hardwood lumber, supporting the forces from the gas springs.
The twin gas piston design shares the lifting load between two pistons, easing opening effort and moderating closing speed for more controlled platform movement.
This bed lift mechanism is designed to be used without a box spring, so the mattress rests directly on a solid platform connected to the lift hardware.
The X22400S bed storage lift mechanism gas spring assisted system from Selby Furniture Hardware provides a defined structure for building a lifting bed platform around a 209 lbs per pair target weight. The ability to orient the gas spring assisted mechanisms for side or end opening supports a range of room layouts and storage access approaches. Frame material requirements of 3/4 inch hardwood plywood or 4/4 hardwood lumber set a clear baseline for structural design, while the 6 to 10 inch standard innerspring or foam mattress range aligns with typical sleeping setups. For bed hardware projects centered on under-bed storage with gas spring assistance, this 48 inch lift mechanism offers a focused solution.