Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Bed storage lift mechanism gas spring assisted hardware from Selby Furniture Hardware uses gas spring assisted mechanisms to raise a bed platform, so the platform can be opened for access to under-bed storage while the springs support the load. The product is a bed storage lift mechanism with twin gas pistons, so the lift is assisted in both opening and closing motions, which helps control movement. Each assembly is designed as a one-piece unit, so the lift mechanism is handled as a single component when positioning it on the bed frame. The lift hardware is targeted for a total platform, mattress, and bedding weight of 110 lbs per pair, so performance is matched to typical residential bed loads within that range. This bed hardware is part of the builders hardware and bed hardware category, so it fits into standard woodworking and furniture projects that call for under-bed storage access.
The gas spring assisted mechanisms are oriented on the bed so that the lift opens from either the side or the end, which allows the hardware to be laid out to clear walls or adjacent furniture. The lift hardware is designed to be used without a box spring, so the mattress and platform act together as the lifted structure. Material for the bed frame should equal or exceed 3/4 inch hardwood plywood or 4/4 hardwood lumber, so the frame provides sufficient structure to support the lift forces from the gas pistons. Using a 6-10 inch thick standard innerspring or foam mattress aligns with the target design weight, so the gas springs operate within their intended load range during everyday use.
This bed storage lift mechanism gas spring assisted product is suited to beds where the platform needs to open from the side or end, so it fits storage bases that run along walls or free-standing frames. The 36 inch length of the lift hardware sets the scale of the mechanism, so it pairs with typical bed platform dimensions that can accommodate that lift arm length. The target weight of 110 lbs per pair, defined as the total weight of platform, mattress, and bedding, guides selection of platform materials and mattress types so the lift effort stays manageable. Using a 6-10 inch thick standard innerspring or foam mattress keeps the mattress mass within the intended range, so the gas pistons do the work they are designed for in lifting and lowering. The requirement that material for the bed frame should equal or exceed 3/4 inch hardwood plywood or 4/4 hardwood lumber ties the hardware to solid wood or plywood construction, so the lift reaction loads are carried by structural members that can handle repeated use.
The gas spring assisted mechanism uses twin gas pistons to provide easy open and safe close, so the forces during operation are moderated by the springs rather than being carried entirely by the user. Because the mechanisms can be oriented to open from side or end of the bed, the lift can be laid out to give clear access to storage without interfering with nearby casework or doors. Each lift mechanism is fully assembled into a one-piece unit, so alignment is built into the factory assembly and the installer works with a stable, pre-aligned mechanism on each side. The design to be used without a box spring keeps the lifted mass closer to the platform, so the gas springs operate on a consistent geometry every cycle. Matching the total weight of platform, mattress, and bedding to the 110 lbs per pair target maintains the balance point of the gas springs, so lift effort and closing behavior remain consistent over time in normal furniture use.
The bed storage lift mechanism gas spring assisted product is part of bed hardware, so it is intended for bed platforms that need to lift for access to storage space.
The gas spring assisted mechanisms can be oriented to open from side or end of the bed, so layout can follow room constraints and preferred access direction.
The bed storage lift mechanism gas spring assisted system specifies bed frame material that equals or exceeds 3/4 inch hardwood plywood or 4/4 hardwood lumber for structural support.
The gas spring assisted mechanisms are intended for use with a 6-10 inch thick standard innerspring or foam mattress, aligning the mattress mass with the target lift weight.
The bed storage lift mechanism gas spring assisted hardware is targeted for 110 lbs per pair total platform, mattress, and bedding weight, so lift force and closing behavior match that combined load.
Each lift mechanism is fully assembled into a one-piece unit, so installation focuses on positioning and securing the mechanism rather than assembling multiple linkage parts.
This bed storage lift mechanism gas spring assisted assembly from Selby Furniture Hardware pairs twin gas pistons with a 36 inch length, so it fits many bed storage builds that need controlled lifting. The ability to orient the mechanism for side or end opening gives layout flexibility, while the 110 lbs per pair target weight, based on total platform, mattress, and bedding, defines the operating range. For projects built with 3/4 inch hardwood plywood or 4/4 hardwood lumber and using a 6-10 inch innerspring or foam mattress, this hardware provides a defined gas spring assisted solution for under-bed storage access.