Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Epoch Edge pull 160mm center to center describes a Berenson Corporation handle from the Century Edge collection that spans 6-5/16 inches between screw holes, so cabinet layouts follow a consistent, repeatable drilling pattern across doors and drawers. The pull is made from solid brass, giving the handle a dense feel that supports frequent use on busy kitchen, bath, or shop casework. Its Verona Bronze finish defines the visual tone, helping installers match this handle with other Verona Bronze decorative hardware on the same project. Overall length of 7-1/8 inches sets the grip size, giving users a defined area to grab on larger drawer fronts. With a projection of 1-5/16 inches, the handle stands off the face of the cabinet, creating finger clearance for a comfortable pull motion. A width of 5/8 inch controls the front profile, guiding layout around adjacent hardware or tight reveals.
This Berenson Epoch Edge Series pull uses a center to center dimension of 6-5/16 inches, so hole spacing on the door or drawer front follows that exact distance for mounting. The 7-1/8 inch overall length extends slightly beyond the mounting points, which affects how close the handle can sit to edges or neighboring hardware on narrow fronts. Projection of 1-5/16 inches sets how far the userâ??s hand moves away from the cabinet face, which matters for clearance over raised panel profiles or applied moldings. With a width of 5/8 inch, the handle presents a slim footprint across the face, helping installers fit it between stiles or along narrow drawer rails. The pullâ??s solid brass construction maintains this geometry under normal operating loads, so alignment stays stable after installation.
The Epoch Edge pull in Verona Bronze sits within Berensonâ??s Century Edge material and finish mix, so it aligns visually with other Century Edge pieces on coordinated cabinet runs. Its 6-5/16 inch (160 mm) center to center sizing targets cabinets and drawers designed for longer pulls, such as kitchen bases, tall pantry doors, or wide bath vanity drawers. The 7-1/8 inch overall length means the pull covers more of the rail or drawer face, which works well on medium to large fronts where a small handle would look undersized. A projection of 1-5/16 inches offers space for fingers behind the pull, which is useful on thicker door profiles or fronts with decorative edges. The 5/8 inch width yields a narrow frontal band, keeping the hardware visually light so the cabinet material and finish remain prominent.
The precise 6-5/16 inch center to center measurement allows installers to standardize drilling templates, cutting down layout steps when there are many drawers using this pull. Solid brass construction supports the threaded engagement of the specified screw size, helping the pull stay tight on repeated openings over time. The Verona Bronze finish gives a defined color target when selecting hinges or other decorative hardware, which simplifies coordination during project planning. The 7-1/8 inch overall length sets a clear outside dimension, allowing fabricators to maintain consistent end clearances from door edges or appliance panels. Projection of 1-5/16 inches defines how far the hand sits from the cabinet face, which can help reduce finger contact with finished wood or laminate surfaces during operation. The 5/8 inch width provides a consistent visible band, aiding in alignment when multiple pulls must line up across multi-drawer stacks.
The Epoch Edge pull has a 6-5/16 inch, or 160 mm, center to center dimension, so mounting holes on cabinet doors or drawers are drilled at that spacing for proper alignment.
The Berenson 1219-10VB-P pull has an overall length of 7-1/8 inches, which sets how much of the door or drawer edge it covers on the cabinet face.
The Century Edge pull is made from solid brass, giving the handle a substantial feel that supports repeated daily use on doors and drawers.
This Verona Bronze cabinet pull has a projection of 1-5/16 inches, providing space for fingers behind the handle while keeping the profile relatively low.
The Epoch Edge Series brass pull has a width of 5/8 inch across the front, giving it a slim visual profile on cabinet doors and drawer fronts.
This Verona Bronze pull belongs to Berenson's Century Edge collection, so it coordinates with other Century Edge decorative hardware on matching cabinet installations.
The Epoch Edge pull 160mm center to center specification gives cabinetmakers a fixed drilling standard for doors and drawers using this handle. Solid brass construction and a Verona Bronze finish provide a defined material and color, so hardware plans can follow the Century Edge collection across a project. With 7-1/8 inch overall length, 1-5/16 inch projection, and 5/8 inch width, the pull offers known working dimensions that simplify layout decisions. For jobs calling for a Berenson Verona Bronze handle in this size range, this part number delivers a clearly defined set of mounting and visual characteristics.
Sold In: 1 Each
