Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Hickory Hardware Conquest Series 3 inch pull gives you a matched set of handles for cabinetry, so your doors and drawers line up visually across a run. The 3 inch (76 mm) center to center measurement sets a consistent drilling layout, which keeps installation straightforward on face frames or panels laid out for this common size. The satin nickel finish establishes a neutral, modern look that works with a range of fronts, so you can standardize hardware across multiple rooms. The pull length of 5 inches provides a wider gripping area than the bore spacing alone, which helps fingers clear the cabinet surface during daily use. A projection of 1 inch brings the hand away from the door face, which reduces knuckle contact on thicker fronts. The 1/2 inch width keeps the pull visually light while still defining a clear grab point along the rail.
The 3 inch (76 mm) center to center value defines the mounting hole spacing, which lets you set up repeatable drilling on templates or boring equipment cut for this standard pattern. With a 5 inch overall length, the pull covers the bore points while leaving enough bar at each end for a clean visual on wider rails. The 1 inch projection creates a reliable clearance pocket between the hand and door face, which suits installations on thicker fronts where shallow pulls feel tight. A 1/2 inch width keeps the footprint narrow on the stile or rail, which can help when aligning hardware on narrower frame members. The satin nickel finish on the Belwith Keeler pull keeps the contact surface smooth for sliding grips, which supports consistent operation over time on frequently cycled cabinets.
This Belwith Keeler cabinet pull sits in the Decorative Hardware & Moldings Handles and Pulls category, which positions it for doors and drawers where appearance and function both matter. The 3 inch center to center layout matches a common cabinet drilling standard, which works well on face frame cabinets, frameless boxes, and shop storage set for that spacing. Its 5 inch length gives proportion on standard kitchen and bath door rails, so runs of hardware look balanced across multiple fronts. The satin nickel finish lines up with many hinge and knob finishes, which helps maintain a unified look when you are coordinating different pieces of visible hardware. With zinc construction, the pull suits jobs where a metal handle is preferred over non-metal options, such as heavier drawer stacks or frequently accessed wall cabinets.
The clearly defined 3 inch (76 mm) center to center dimension lets you use fixed jigs for drilling, which makes it easier to keep handle positions consistent across large cabinet runs. The 1 inch projection gives reliable stand-off from the door surface, which reduces interference when doors swing past adjacent faces or meet at corners. At 1/2 inch wide, the pull allows precise placement on narrow rails without crowding edge profiles, which helps when aligning multiple pulls vertically on tall cabinets. The 5 inch length helps your layout read straight because each handle overhangs the bore positions evenly, which is useful when setting a visual line across a bank of drawers. The satin nickel finish provides a uniform surface across all pieces in the economy pack, which keeps reflective differences from drawing attention along a completed installation.
This Hickory Hardware Conquest Series 3 inch pull uses a 3 inch (76 mm) center to center drilling pattern, which matches a common cabinet layout for doors and drawers.
The VP14174-SN pull has a 1 inch projection, which creates hand clearance between the bar and cabinet surface during opening and closing.
This Belwith Keeler satin nickel pull has a 5 inch overall length, which visually spans more of the rail while keeping the 3 inch mounting pattern.
The Hickory Hardware Conquest Series pull is made from zinc, which provides a metal construction suited to regular cabinet door and drawer use.
The VP14174-SN cabinet pull uses a satin nickel finish, which offers a muted metallic appearance for decorative cabinet installations.
This 3 inch center to center cabinet pull has a 1/2 inch width, which gives a slim profile while still presenting a defined gripping bar.
This Hickory Hardware Conquest Series 3 inch pull pairs a 3 inch (76 mm) center to center pattern with a 5 inch length, giving you a practical layout that suits many cabinet doors and drawers. The zinc construction and satin nickel finish provide a metal handle with a neutral look, useful when matching other visible hardware on the job. With its defined projection and width, this Belwith Keeler pull offers predictable hand clearance and footprint. Use the VP14174-SN part number when specifying or reordering so installations across projects stay consistent.
Sold In: 1 Package
