Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Dynabrade Dynacut 180 grit sanding sheet is a PSA silicon carbide on film sanding sheet sized at 2-3/4 x 3-1/2 inches, so it suits small-area surface work where controlled hand sanding or block sanding is needed. The sheet uses silicon carbide grain that creates a thinner scratch than aluminum oxide, which helps when a finer scratch pattern is required before moving to finishing steps. The silicon carbide grain will cut faster than aluminum oxide, which lets you remove light imperfections or residues with fewer passes. Because this grain does not last as long as aluminum oxide, it is best applied where fast cutting on smaller areas matters more than extended life. The abrasive sheet is described for light deburring and scouring, aligning it with cleanup, edge touch-up, and surface preparation tasks. The film backing supports consistent scratch formation, which helps maintain even surface quality across the contact area.
This PSA silicon carbide on film sanding sheet is designed to adhere by its pressure sensitive adhesive backing, so it mounts quickly on an appropriate sanding block or holder and stays in place under light deburring and scouring loads. The 2-3/4 x 3-1/2 inch size keeps the abrasive area compact, which helps when working on edges, profiles, or localized defects where a full-size sheet would be cumbersome. Because the silicon carbide grain cuts faster but does not last as long as aluminum oxide, it is suited to short runs or finishing-related prep where rapid cutting on a small footprint is valued more than long wear. The film backing under the abrasive layer supports a uniform surface that helps the PSA sheet sit flat against the tool face, aiding even scratch formation across the work zone.
This abrasive sheet is described specifically for light deburring and scouring, so it fits operations where you are knocking down small burrs or residues rather than reshaping stock. The 180 grit silicon carbide grain generates a thinner scratch than aluminum oxide, which supports a smoother transition from deburred surface to final sanding or finishing. Because silicon carbide will cut faster than aluminum oxide, the sheet removes minor high spots, flash, or surface contamination in fewer strokes, which is useful on repeat light clean-up tasks. The compact 3-1/2 inch by 2-3/4 inch format supports controlled hand pressure around corners, edges, and detail areas, making it suitable for touch-up work on smaller components. The film backing paired with the PSA construction promotes a stable contact patch that helps keep the deburring action consistent along the pass path.
The silicon carbide on film design provides a sharp grain on a smooth, dimensionally stable backing, which helps maintain predictable scratch depth during light deburring and scouring. Because the grain cuts faster but does not last as long as aluminum oxide, each new sheet delivers aggressive initial performance that favors time-sensitive or repetitive prep operations. The PSA backing lets the sheet adhere tightly to a compatible sanding block or pad, so the abrasive surface moves as one with the tool and supports even material removal. The 2-3/4 x 3-1/2 inch sheet size pairs well with small blocks or specialty holders, which makes it easier to follow contours or reach confined zones without excess overhang. These characteristics align the sheet with tasks where consistent scratch, good control, and fast cutting on limited areas help reduce rework between sanding stages.
The sheet uses silicon carbide grain, which creates a thinner scratch than aluminum oxide and cuts faster, supporting finer surface preparation on light deburring and scouring tasks.
The 180 grit silicon carbide creates a thinner scratch pattern, which leaves a finer surface that transitions more cleanly into subsequent sanding or finishing stages.
The sheet measures 3-1/2 inches (89 mm) wide by 2-3/4 inches (70 mm) long, supporting controlled sanding on smaller areas, edges, and detailed components.
This silicon carbide sheet cuts faster but does not last as long as aluminum oxide, which favors short, targeted light deburring and scouring where speed and finer scratch are priorities.
The sheet is described for light deburring and scouring, fitting tasks such as cleaning small burrs, residues, or surface imperfections before further sanding steps.
The PSA silicon carbide on film construction lets the sheet adhere to a suitable block while the film backing supports a flat, consistent sanding surface for even scratch formation.
The Dynabrade Dynacut 180 grit PSA silicon carbide on film sanding sheet combines fast-cutting silicon carbide grain with a thinner scratch pattern, so it fits light deburring and scouring where surface quality matters. Its 3-1/2 inch by 2-3/4 inch size supports controlled work on edges, profiles, and localized defects. The PSA-backed film construction helps keep the abrasive surface flat and stable against a suitable holder, which assists in maintaining consistent results from piece to piece. For applications centered on small-area cleanup and finishing-stage preparation, this sheet aligns well with workflows that value precise control and efficient material removal.
Sold In: 50 Each