1 inch Diameter x 1/2 inch Long Standoff Kit gives you a matched set of components to mount a sign or display at a fixed, uniform offset from the wall. The Pro Value Series product is designed as a complete standoff kit for installing a sign or display, so every piece works together as a single mounting system. The 1 inch diameter size of the standard caps provides a broad bearing surface on the sign face, which helps spread the load at each mounting point. The 1 inch diameter by 1/2 inch long barrels hold the face material off the wall at a consistent 1/2 inch depth, creating a clean, stand-off look. Black anodized finish on the visible parts gives the mounted sign or display a dark, uniform appearance that blends with black graphics and trim.
The black anodized finish on the caps and barrels defines the visible hardware appearance whenever the sign or display is installed. The 1/2 inch long barrels establish the projection from the wall, creating a defined gap that reads consistently across all four mounting points. Studs sized for material up to 3/8 inch thick work with sign substrates within that range, so the assembly clamps the material between cap and barrel without excessive thread exposure at the front. Combination screws act as the fastening point between barrel and wall, then the barrels support the studs and caps, forming a straightforward, layered mounting stack.
This Pro Value Series standoff kit is described as a complete standoff kit for installing a sign or display, so it fits jobs where a flat panel needs to be mounted off the wall with visible hardware. The 1 inch diameter standard caps suit typical sign and display panel sizes where four mounting points can carry the load. Barrels at 1/2 inch length are suited to applications where a modest stand-off is preferred, providing separation from the wall without pushing the sign excessively forward. Studs that are specified for material up to 3/8 inch thick target sign materials in that thickness range, aligning the kit with many common rigid substrates.
The SZG4005 kit uses matched 1 inch diameter caps and 1 inch diameter by 1/2 inch long barrels, which keeps all visible hardware consistent at each mounting point and simplifies layout because every standoff footprint is the same. The defined 1/2 inch barrel length means each installation yields the same projection, so multiple signs mounted with this kit line up at the same stand-off depth. Studs for material up to 3/8 inch thick enable the installer to work within a known panel thickness range and achieve reliable clamping of the panel between cap and barrel. Combination screws and multi-purpose nylon anchors form a coordinated wall attachment method, so the same screw and anchor combination ties the barrel to the substrate. Bringing these components together as a complete standoff kit allows the installer to work from a single part number on repeat projects, which simplifies both site preparation and reorders.
The 1 inch diameter refers to both the standard caps and the barrels, so the visible hardware at the front and the barrel body share the same footprint on the sign surface.
The kit uses barrels that are 1/2 inch long, so the sign or display face sits about 1/2 inch away from the wall at each mounting point.
The studs in this Pro Value Series kit are specified for material up to 3/8 inch thick, so panels within that thickness range can be clamped between the caps and barrels.
The standoff kit is described as black anodized, so the caps and barrels present a dark anodized finish on the installed sign or display.
The combination screws connect the barrels to the wall while working together with the multi-purpose nylon anchors to secure the mounting points.
SZG4005 identifies this specific Pro Value Series standoff kit configuration, grouping the 1 inch diameter caps, 1 inch by 1/2 inch barrels, studs, screws, and nylon anchors.
The Pro Value Series 1 inch Diameter x 1/2 inch Long Standoff Kit, Black Anodized, brings caps, barrels, studs, combination screws, and multi-purpose nylon anchors together under one SZG4005 part number. For sign or display installs using material up to 3/8 inch thick and a 1/2 inch stand-off, this kit gives a consistent black anodized appearance and a repeatable mounting method ready for use on your next project.
Sold In: 1 Kit