Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
This Würth M7 x 50mm confirmat screw is built for butt-joint assembly in particleboard, MDF, and melamine-faced panels. The blunt point installs into a stepped pilot hole bored with a confirmat step-drill bit, producing a precise, repeatable joint that pulls cabinet and furniture components tight without splitting the panel edges.
Confirmat screws are the standard fastener for butt joints in 32mm system cabinetry, flat-pack furniture, and RTA product manufacturing. The joint geometry depends on a stepped pilot hole that is bored in a single pass with a confirmat step-drill bit: the drill creates a clearance hole through the near-side panel, a shank hole through the joint, and a head recess at the surface all at once. The blunt point on this screw drops straight into that prepared hole without self-starting, which is exactly what the confirmat system is designed for. Attempting to drive a blunt-point confirmat without the correct step-drill preparation will not produce a clean joint.
The 50mm length suits typical cabinet carcass construction where a 16mm or 19mm panel side meets a shelf or base of similar thickness, giving the threaded section enough embedment to hold the joint under normal load. The coarse thread bites into the fiber matrix of particleboard and MDF, materials where finer threads lose pull-out strength.
The screw is steel with a zinc finish, appropriate for dry indoor assembly in kitchen cabinets, bath vanities, office furniture, and shelving units. The zinc coating is not rated for exterior or high-humidity environments. The Pozidriv #3 drive recess accepts a PZ3 bit, and the parallel flanks of the Pozidriv geometry hold the bit under power-tool torque better than a comparable Phillips recess. This matters in production work where the same bit is driven hundreds of times per shift. No nibs are present under the flat head, so a confirmat step-drill that includes a head countersink in the stepped bore is required for a flush-seated result.
Cabinet shops running 32mm system construction use confirmat screws as a primary carcass fastener because the joint is strong, removable, and repeatable. A technician with a confirmat step-drill bit and a PZ3 driver can assemble a cabinet box in fewer operations than pocket-hole or dowel alternatives. The 1000-piece box quantity supports shops that build at volume and need a reliable supply of a single, consistent fastener size. Furniture manufacturers building melamine or thermofoil case goods find the same advantage: one drill pass, one drive, one tight butt joint. The flat head with its unthreaded shoulder is what makes the joint work mechanically, pulling the two panels flush without the thread engaging the near-side panel and preventing full closure.
This M7 screw requires a confirmat step-drill bit sized for a 7mm shank. The bit bores the shank hole, clearance hole, and head recess in one pass. Using the wrong bit size will produce a loose or improperly seated joint.
The unthreaded shoulder slides freely through the near-side panel. Only the threaded section engages the second panel, which allows the head to draw both pieces tightly together. A fully threaded shank would grip both panels and prevent the joint from closing flush.
Confirmat screws are engineered for particleboard, MDF, and melamine-faced engineered panels. They are not the standard choice for solid wood joinery, where pocket-hole screws, wood screws, or mortise-and-tenon construction are more appropriate.
Yes. A PZ3 Pozidriv bit is required. A standard Phillips #3 bit fits loosely in the Pozidriv recess and will cam out under torque, damaging the head. Pozidriv bits are widely available and are the correct tool for this drive.
Yes. The confirmat joint can be disassembled by reversing the screw. This is one reason the confirmat system is common in flat-pack and RTA furniture, where the ability to break down and reassemble a piece has value.
When the confirmat system is already in your workflow, having 1000 screws of a consistent size on hand keeps production moving without mid-run restocking. The M7 x 50mm size covers the majority of standard cabinet carcass joints, and the Pozidriv #3 drive holds up through high-volume power driving.
Sold In: 1000 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 10 Each |  WW614176653 Mfr# 0614176653090 10 | #3 x 1" Pozidriv Insert Bit |