DH Caster 8" Plate Mount Swivel Caster, Polyolefin, No Brake, 900 lb, C-MHD8HDPS

Swivel Caster With 8 Inch Polyolefin Wheel

swivel caster with 8 inch polyolefin wheel from DH Casters uses a heavy plastic polyolefin wheel, so it rolls on a hard, non-marking tread that supports loads while helping protect floors in normal material-handling environments. The caster is rated at 900 lb load capacity, so it handles heavy setups on platform trucks, flatbed carts, containers, automotive equipment, distribution carts, and warehouse equipment where single-point loading can get high. A plate mount design with a 3-15/16 inch by 4-1/2 inch plate spreads the load over a larger footprint, which helps the caster carry weight steadily under carts and trucks. The swivel type construction lets the wheel rotate for directional changes, so carts can maneuver into tight aisles and work cells. This caster is identified as manufacturer part C-MHD8HDPS, which ties directly to DH Casters documentation for repeat orders and matching existing units in the field.

Key Plate Mounted Caster Details For Jobsites

• The 8 inch wheel diameter raises carts higher off the floor, which helps the caster roll over minor floor joints or debris commonly found around platform trucks and warehouse equipment.
• A 2 inch tread width provides a stable contact patch, so the caster supports heavy loads on flatbed carts and containers without digging into typical hard industrial floors.
• The heavy plastic polyolefin wheel material provides a firm, non-marking running surface, which matters where floors must stay clean under automotive equipment and distribution carts.
• A 900 lb load capacity gives each caster substantial carrying ability, so designers can plan total cart ratings for warehouse equipment around known per-caster limits.
• The plate size of 3-15/16 inch by 4-1/2 inch creates a large mounting area, which spreads forces into the cart frame when the caster supports moving or stationary loads.

Plate Mount Swivel Caster Fit And Setup

This DH Casters swivel caster uses a plate mount from the plate mounted casters category, so it fastens flat against a mating surface on platform trucks, flatbed carts, containers, automotive equipment, distribution carts, and warehouse equipment. The 3-15/16 inch by 4-1/2 inch plate size defines the footprint on the cart frame, which helps layout bolt patterns and steel plate sizing during fabrication. Its swivel type construction lets the caster rotate under the mounting plate, so carts can track straight or pivot into position as needed in shop aisles. With an 8 inch wheel diameter and 2 inch tread width, the caster provides height and stance that affect deck level and clearance planning on new builds or retrofits. The 900 lb capacity gives installers a clear limit per caster, which guides how many casters to place under heavier assemblies.

Using This DH Casters Swivel Caster In Workflows

Where This Plate Mounted Caster Is Applied

This DH Casters swivel caster is specified for platform trucks, so it supports rolling decks that move materials between work areas. The same 900 lb capacity rating serves flatbed carts and containers, where heavy loads must move without overloading a single wheel position. In automotive equipment layouts, the 8 inch polyolefin wheel diameter and 2 inch tread width support fixtures and tooling that travel around service bays. Distribution carts also benefit from the non-marking polyolefin wheel type, because it supports frequent movement through aisles without leaving marks on typical facility floors. Within warehouse equipment setups, the plate mount construction ties directly into steel frames, so this caster forms a structural rolling point under racks or carts. The manufacturer part C-MHD8HDPS designation keeps this caster consistent across multiple pieces of equipment.

Details That Support Repeatable Cart Performance

The swivel caster with 8 inch polyolefin wheel design allows rotation under load, which lets operators change direction smoothly when positioning platform trucks or distribution carts. A 2 inch tread width on the heavy plastic polyolefin wheel type balances footprint and maneuverability, so carts feel stable yet steer predictably in confined warehouse equipment lanes. The 3-15/16 inch by 4-1/2 inch plate mount size standardizes the mounting pattern, which simplifies building multiple flatbed carts or containers using the same frame drilling or welding layout. The 900 lb load capacity per caster provides a direct number for planning total cart capacity, so equipment designers can scale caster count to expected weight on automotive equipment stands or warehouse carts. Being part of the plate mounted casters category anchors this caster in a known mounting style, which helps match it with existing fabrication practices in shops working with steel or heavy wood frames.

Common Questions About This Swivel Caster

Choose This Caster For Heavy Cart Applications

The DH Casters C-MHD8HDPS swivel caster with 8 inch heavy plastic polyolefin wheel, 2 inch tread width, and 900 lb load capacity offers a plate mounted casters solution for platform trucks, flatbed carts, containers, automotive equipment, distribution carts, and warehouse equipment. The 3-15/16 inch by 4-1/2 inch plate mount design ties into common cart and equipment frames, while the non-marking polyolefin wheel type supports frequent rolling on typical facility floors. For builds or replacements that call for this exact configuration, selecting this caster keeps equipment performance aligned with its specified rating and mounting layout.