Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
solid surface seam cartridge describes this 9 oz solid surface seam cartridge in frosted gray that is formulated as a two-part methacrylate surfacing adhesive, so seams between panels can be formed as a bonded joint rather than a mechanical break. The adhesive is designed for seamless bonding of solid surface, engineered stone, and natural stone products, so one product can serve across different surfacing materials on the same project. Its ultra violet light stable, non-yellowing formulation keeps the bonded seam closer in appearance to the surrounding surface over time under normal light exposure, which matters on visible joint lines. The product provides a combination of high strength, stiffness, and toughness, so once cured the joint helps the assembly act as a continuous surface under typical service loads.
This two-part methacrylate surfacing adhesive is supplied in a 9 oz solid surface seam cartridge in frosted gray, so it is set up for cartridge-based application equipment that meters and mixes the two components as they are dispensed. The combination of high strength, stiffness, and toughness means that, once placed into a properly prepared joint and allowed to cure, the adhesive creates a joint that supports the adjoining pieces in alignment under load. Its excellent heat resistance and bond strength mean that bonded seams retain their integrity under typical temperature changes, so the joint line continues to support the surface in use. High solids means extended mileage, so installers can run longer beads between clamping points before needing a new cartridge.
This seam adhesive is designed for the seamless bonding of solid surface (acrylic and polyester and blends), engineered stone, and natural stone products, so it fits work where slabs or sections must be joined into larger assemblies. By bonding very strongly to a wide variety of solid surface materials, the adhesive supports builds that combine different solid surface formulations across a run. It provides high strength bonds to acrylic solid surface, polyester solid surface (both filled and unfilled), and alloy solid surface, so fabricators working with these materials can form joints that help the finished top behave as a single unit in normal service. Because it is ultra violet light stable and non-yellowing, the frosted gray seam stays closer to its intended tone along exposed edges.
The combination of high strength, stiffness, and toughness in this two-part methacrylate surfacing adhesive means cured joints are built to support both load bearing and everyday impact across the seam area, so workpieces remain aligned as the installation is used. Its excellent heat resistance and bond strength mean that short-term temperature changes around the joint do not readily compromise the bond, so surfaces maintain continuity in typical room and service conditions. High solids means extended mileage, which lets each 9 oz solid surface seam cartridge in frosted gray cover more seam length before replacement, so longer runs can be addressed with fewer cartridge changes during fabrication. The OTC compliant, no-urea formaldehyde added formulation addresses regulatory requirements while still providing the structural bonding performance needed in normal surfacing work.
The adhesive is designed for seamless bonding of solid surface (acrylic and polyester and blends), engineered stone, and natural stone products, so it serves across common countertop and surfacing materials.
The 9 oz solid surface seam cartridge in frosted gray provides a controlled seam color, so joints can visually blend with compatible surfaces where a frosted gray tone is appropriate.
The ultra violet light stable, non-yellowing formulation keeps the adhesive from yellowing as it ages, so visible seams stay closer to their original appearance under normal light exposure.
High solids means extended mileage, so each cartridge can cover more seam length, helping reduce cartridge changes on longer joints during fabrication or installation.
The combination of high strength, stiffness, and toughness lets the cured joint support loads and resist deformation, so adjoining pieces act more like a single surface in service.
The product provides high strength bonds to acrylic solid surface, polyester solid surface (both filled and unfilled), and alloy solid surface, so it supports varied solid surface formulations.
This Formica Adhesives seam adhesive, supplied as a 9 oz solid surface seam cartridge in frosted gray, is designed for seamless bonding of solid surface, engineered stone, and natural stone. Its two-part methacrylate, ultra violet light stable, non-yellowing formulation offers high strength, stiffness, and toughness with excellent heat resistance and bond strength for joints. With high solids for extended mileage and OTC compliant, no-urea formaldehyde added properties, it is set up for fabricators needing structural bonding across acrylic, polyester, and alloy solid surface materials.
Sold In: 1 Each