12" x 20" Alpine Bar Top Support, Steel Finish
Description
Alpine Bar Top Support For Elevated Counters
Alpine Bar Top Support is a 12 x 20 unfinished steel bracket from Federal Brace designed to elevate and hold a counter or bar over a subcounter, so you can build a raised bar top above a base cabinet. This Alpine Elevated Counter Support installs on the base cabinet to create an elevated counter, turning a standard run into a bar perfect for eat-in kitchens and similar layouts where a higher serving or seating surface is needed. The Alpine model will support a 14 to 20 inch deep counter, giving you a defined range for bar top depth when planning overhang and cabinet placement. The material thickness of the Alpine Elevated Counter Support is 0.25 inch, which provides substantial section strength for carrying vertical loads over the bracket span. Bar top supports are described as fine hardware that enhances any kitchen, tying structural support and finished design into a single component.
Key Bar Top Support Details For Planning
- The 12 x 20 inch size defines the horizontal and vertical legs of the support, helping you set elevation and projection when laying out the bar over the base cabinet face and deck.
- The Alpine model supports a 14 to 20 inch deep counter, so bar top depth and overhang can be designed within a known capacity range for both new work and retrofit projects.
- The carry capacity of 500 pounds each means every support can handle heavy counter materials, which is critical when spacing multiple brackets along a run.
- The material thickness of 0.25 inch provides a robust steel section, adding stiffness that reduces deflection under load along the bar top edge.
- The unfinished steel finish allows field painting, so the support can match surrounding cabinetry or trim while also addressing corrosion resistance needs.
- Three 0.26 inch straight mounting holes provide fixed locations for fasteners, which simplifies marking, drilling, and anchoring into the base cabinet structure.
Mounting And Installation Use On Base Cabinets
This Alpine Bar Top Support installs on the base cabinet, so the bracket becomes the structural link between cabinet carcass and elevated counter. Installation can be at the time of new construction or added later in a remodel or retrofit, which lets you plan raised bar tops into fresh layouts or upgrade existing counters without changing the entire base run. The three 0.26 inch straight mounting holes are designed for straight mounting, giving a consistent fastener pattern that speeds layout and alignment across multiple supports. Because the material thickness is 0.25 inch, the bracket presents a stable surface for fastening the elevated counter or bar, helping keep the bar top level along its length.
Why This Counter Support Fits Real Kitchen Projects
Using The 12 x 20 Support In Kitchen Layouts
The 12 x 20 Alpine Bar Top Support from Federal Brace works as a workstation and countertop bracket for creating an elevated bar top above a subcounter. By mounting this support on the base cabinet, the elevated counter is held above the lower surface, which is useful where a separation between prep area and serving or seating area is desired. The Alpine model will support a 14 to 20 inch deep counter, so typical bar depth dimensions fall inside the rated range, making it practical for many standard kitchen bar configurations. Because bar top supports are considered fine hardware that enhances any kitchen, the Alpine support serves both structural and visual roles in the finished installation.
Details That Help Support Heavy Bar Tops Reliably
The carry capacity of 500 pounds each means each Alpine Elevated Counter Support can take substantial vertical load, which matters when working with dense countertop materials or extended bar spans. The 0.25 inch material thickness combines with the 12 x 20 geometry to provide the strength necessary to elevate and hold a counter or bar over a subcounter, so the raised surface stays supported during everyday use. Three 0.26 inch straight mounting holes give a defined pattern for fasteners, which helps transfer load from the bracket into the base cabinet structure and keeps installation repeatable from bracket to bracket. The unfinished steel finish allows the support to be painted to avoid corrosion, which is important for long-term performance where moisture from routine kitchen use may contact the bracket surface.
Common Questions About Alpine Bar Top Support Use
What counter depth can the Alpine Bar Top Support handle?
The Alpine Bar Top Support will support a 14 to 20 inch deep counter, so bar tops within that depth range stay within the stated design capacity.
How much weight can one Alpine Elevated Counter Support carry?
The Alpine Elevated Counter Support has a carry capacity of 500 pounds each, allowing it to support heavy countertop materials when spaced appropriately along a run.
Where is the Alpine Bar Top Support installed in relation to the cabinets?
The Alpine Bar Top Support installs on the base cabinet, acting as the structural connection between the cabinet and the elevated counter or bar above the subcounter.
Can this 12 x 20 bar top support be used in remodel or retrofit projects?
The Alpine Bar Top Support can be installed at the time of new construction or added later in a remodel or retrofit, so it suits both new layouts and upgrades.
What material and thickness is the Alpine counter support made from?
The Alpine counter support is made from unfinished steel with a material thickness of 0.25 inch, providing strength and a paintable surface for corrosion control.
How does the 12 x 20 size affect bar top layout?
The 12 x 20 size defines vertical rise and horizontal projection, helping determine bar height over the subcounter and how far the elevated top extends from the cabinet.
Select This Steel Support For Elevated Bar Tops
The Alpine Bar Top Support 12 x 20 bracket from Federal Brace provides the support strength necessary to elevate and hold a counter or bar over a subcounter on a base cabinet. With a 500 pound carry capacity for each support and a 14 to 20 inch counter depth range, this workstation and countertop bracket suits many bar top layouts in kitchens and similar spaces. The 0.25 inch unfinished steel construction, three 0.26 inch straight mounting holes, and field-paintable surface give you a defined, workable solution for raised bar installations that need both structure and finish alignment.
