Hickory Hardware Eclipse 3" (76 mm) Center to Center Satin Bronze Pull, P330-SBZ

Hickory Hardware Eclipse Pull For Cabinets And Drawers

Hickory Hardware Eclipse pull is a 3 inch (76 mm) center to center satin bronze pull designed for cabinet and drawer fronts where a compact, consistent grip line is needed. The Eclipse collection identity ties this pull into other Eclipse pieces on a project, so runs of doors and drawers present a unified look. The satin bronze finish gives a muted metallic appearance that softens reflections, which helps finished casework read cleanly under varied lighting. The pull is manufactured from zinc die cast, providing a solid, single-body construction that supports everyday opening and closing loads on residential or light commercial cabinetry. Belwith Keeler branding identifies a decorative hardware line built around coordinated styles, so this specific part number P330-SBZ can be specified repeatedly wherever the same 3 inch layout and finish are required.

Key Eclipse Pull Details For Cabinet Projects

• The 3 inch (76 mm) center to center drilling aligns this pull with standard cabinet boring patterns, which simplifies layout on doors and drawer fronts that already follow common 3 inch spacing.
• The overall 4-1/4 inch length provides finger room beyond the 3 inch fastener spread, giving users a full-width grip area while still fitting on narrow face frames and drawer rails.
• The 1 inch projection sets the hand clearance off the door or drawer face, which helps fingers wrap the pull comfortably without the pull protruding excessively into walk paths.
• The 5/8 inch width creates a slim front profile on the cabinet face, so the pull reads as a clean line while still offering enough surface for a steady, pinch-free grasp.
• The satin bronze finish delivers a warm metallic tone that coordinates with other bronze-colored fittings, supporting a consistent visual scheme across multiple rooms.
• The zinc die cast material yields a dense, single-piece pull body that resists flexing in normal cabinet use, supporting repeated opening and closing on drawers and doors.

Mounting Dimensions And Fit For Eclipse Pull

This Hickory Hardware Eclipse Series pull uses a 3 inch center to center hole spacing, so the mounting holes are set exactly 3 inches apart to align with the pull feet. The specified 4-1/4 inch overall length shows how far the pull extends across the face, which helps when laying out multiple pulls on a run of doors or drawers. A 1 inch projection defines how far the gripping surface stands off the cabinet face, affecting how deep fingers can engage the pull in tight spaces. The 5/8 inch width sets the front view band of the pull, which matters when aligning the pull visually with rail heights, edge profiles, or adjoining hardware on a cabinet elevation.

Eclipse Cabinet Pull Use And Project Planning

Where This 3 Inch Pull Works Best

The 3 inch (76 mm) center to center layout makes this Eclipse Series pull suited to cabinet doors and drawers already bored at that spacing, so existing fronts can retain their hole pattern while upgrading to the P330-SBZ part. The satin bronze finish allows the pull to sit comfortably on painted, stained, or laminated surfaces where a warm metal accent is desired, supporting projects that target coordinated bronze tones across hinges, latches, and other visible components. With a 4-1/4 inch overall length and 5/8 inch width, the pull fits well on both narrow and standard-width rails, which helps maintain proportional hardware sizing from small vanity drawers to wider base cabinets using the same pull model. The 1 inch projection sets the grip away from the face enough to clear typical door profiles, so molded or beveled edges can meet the pull cleanly without crowding the hand space.

Details That Support Repeatable Cabinet Results

The specified center to center, overall length, width, and projection for the P330-SBZ give clear reference points when drafting cabinet shop drawings, so hardware callouts can be repeated across multiple units with predictable alignment. Using a zinc die cast construction on this Belwith Keeler cabinet pull means each piece is formed to a consistent shape, which supports uniform sight lines when several pulls are installed in a row on drawer banks. The satin bronze finish designation provides a defined color and sheen target, making it straightforward to coordinate this pull with other satin bronze cabinet hardware from the same or related collections. Because the Eclipse collection identity is stated, designers can tie this pull into broader Eclipse Series layouts, keeping hardware style and dimensional language consistent from one room or cabinet run to another.

Practical Questions About The Eclipse Series Pull

Selecting The P330-SBZ Pull For Your Next Run

The Hickory Hardware Eclipse Series 3 inch (76 mm) center to center satin bronze pull, P330-SBZ, brings together defined drilling dimensions, a 4-1/4 inch length, 1 inch projection, and zinc die cast construction for cabinet work that depends on repeatable hardware layout. The satin bronze finish and Eclipse collection identity allow this Belwith Keeler cabinet pull to anchor a coordinated hardware scheme across doors and drawers. For projects calling for a consistent 3 inch pull pattern with a warm metal look, this P330-SBZ model from Wurth Baer Supply aligns design intent with clear, job-ready measurements.