Patwin 288 Beige T-Molding, 250' L x 3/4" W - 3/32" Kerf - P500-3/4-288

Patwin Plastics Beige Tee Molding For Clean Edges

Patwin Plastics beige tee molding gives you a 3/4 inch wide edge solution that finishes exposed panels while following typical cabinet and fixture layouts. The 250 ft length per roll supports long runs or multiple projects without frequent material changeovers. The 3/32 inch kerf dimension defines the groove needed in your panel, so cuts can be planned around common saw or router setups. Non-toxic polyethylene construction provides an edge profile suitable for woodworking environments where material safety matters. The Flexene molding design fits any contour whether outside or inside curves and radii, so one profile handles both straight runs and flowing layouts. Consistently precise dimensions help grooves match the barbed stem, which supports secure seating along the entire length. Consistent color across the roll helps finished work look uniform from part to part.

Key Flexene Molding Details That Support Work

• Non-toxic polyethylene is used to manufacture these Flexene moldings, which supports use in woodworking applications where material composition needs to align with shop standards and interior environments.
• The Flexene molding fits any contour whether outside or inside curves and radii, allowing a single tee profile to run across straight sections, convex corners, and concave curves without switching materials.
• Product is consistently precise in dimensions, workability and color, so kerf cuts, bending behavior, and visual appearance can be repeated from job to job for predictable results.
• The design insures the installation will fit firmly and hug edges permanently, helping the barbed stem stay engaged in the 3/32 inch kerf and reducing the likelihood of edge gaps over the run.
• The 250 ft roll length supports long continuous runs or batching multiple parts from the same color lot, which can streamline cutting, grooving, and edging steps in the shop.

Groove Size, Width, And Roll Length In Use

This P500-3/4-288 tee molding uses a 3/32 inch kerf, giving a clear target for the groove that holds the stem, so cut setups can be matched to that slot size. The 3/4 inch width establishes the visible edge coverage, which suits many panel thicknesses used in cabinetry and casework. Each roll is 250 linear feet long, supporting continuous edging without frequent reloading of material during routing and pressing steps. The Patwin Plastics Flexene design helps the molding track along inside and outside curves, so the same groove and profile can be carried through complex layouts. The beige color gives a neutral edge option where a light, unobtrusive trim is desired on finished panels.

How This Beige Tee Molding Fits Shop Work

Tee Molding For Curved And Straight Panel Edges

This Patwin Plastics beige tee molding serves as an edge treatment for panels where a 3/4 inch wide profile is appropriate. The Flexene construction fits any contour whether outside or inside curves and radii, so curved reception desks, rounded display fixtures, or soft-corner casework can use the same profile as straight cabinet sides. Because the molding is manufactured from non-toxic polyethylene, it supports interior woodworking uses where material selection needs to align with shop standards. The tee design works with a 3/32 inch kerf groove, which defines the interface between panel and molding and supports a repeatable routing pattern. With 250 ft of length per roll, larger runs of cabinets or fixtures can be edged from a single roll, which supports consistent color and appearance across every part.

Details That Support Consistent, Firm Edge Results

The P500-3/4-288 part number identifies this specific combination of beige color, 3/4 inch width, and Patwin Plastics Flexene tee profile, which helps keep reorders aligned with existing layouts. Product is consistently precise in dimensions, so once the 3/32 inch kerf and depth are dialed in, the stem engagement can remain consistent from panel to panel. Consistent workability means the same bending behavior can be expected around both outside and inside curves, supporting continuous runs without abrupt changes in handling. Consistent color helps seams between lengths appear uniform, which matters on visible store fixtures and cabinetry. The design insures the installation will fit firmly and hug edges permanently, so the barbed stem works with the properly sized groove to keep the trim tight against the panel edge. The 250 ft roll size supports cutting multiple pieces to length while staying in a single lot of material.

Common Questions About Patwin Flexene Tee Molding

Choose This Beige Tee Molding For Edge Runs

The Patwin Plastics beige tee molding P500-3/4-288 gives you a 3/4 inch profile sized for a 3/32 inch kerf, which aligns well with panel edging workflows in cabinetry and fixture shops. Non-toxic polyethylene construction and consistently precise dimensions support repeatable grooves and tight edges across both straight and curved sections. With 250 ft per roll, this Flexene tee molding suits shops planning continuous edging runs in a neutral beige color. Select this tee molding when a single profile that handles outside and inside curves is needed across multiple panels.