Company Information
Services
Approved US Government VendorCage Code: 1UXJ6
Copyright © 2004-2026, Würth Baer Supply Company. All Rights Reserved.
Copyright © 2004-2026, Würth Baer Supply Company. All Rights Reserved.
Classic Series wall cabinet Brownstone Dartmouth describes a Wolf Home Products wall cabinet built for 42 inch width, 12 inch depth, and 36 inch height, so it fits standard wall runs where that footprint is planned. Two doors with a center stile divide the opening, which helps align door faces and provides a predictable center reference when laying out hardware or adjacent cabinets. The cabinet fronts use 3/4 inch solid maple wood, giving each door a solid frame that supports hinge mounting and resists routine door swing forces. Rails are pocket drilled and assembled with 1 1/4 inch screws, so the face frame joints are mechanically fastened for long-term joint stability during handling and service. Side panels and the bottom are 1/2 inch plywood set in a 1/2 inch dado in the front frame, so the load transfers into the frame instead of relying only on fasteners. Exterior laminate on the side panels matches the finish, which keeps exposed ends visually consistent on wall runs.
The back panels on this Dartmouth Brownstone wall cabinet are glued and nailed into a 1/2 inch dado and stapled to the hang rail and cabinet bottom, so the rear structure works with the hang rail to handle wall loads during mounting. The 1/2 inch plywood sides and bottom, tied into the front frame with glue and staples in a 1/2 inch dado, help the cabinet stay square when it is pulled tight to wall surfaces. The half-depth adjustable shelf is made from 3/4 inch plywood and is held by self-locking 1/4 inch diameter clips on the sides, allowing the shelf height to be changed without tools while the self-locking feature resists accidental dislodging. All-wood 3/4 inch corner blocks at all corners further stiffen the cabinet during lifting into position and anchoring to wall framing.
This Wolf Dartmouth Brownstone wall cabinet is specified at 42 inches wide, 12 inches deep, and 36 inches high, so it spans a wide section of wall and aligns with common wall cabinet height lines. Two doors with a center stile break up the span, which helps control door sag on a 42 inch width and creates a fixed vertical element in the opening for organizing stored items. The cabinet provides two adjustable shelves in addition to the cabinet floor, giving three useable levels when laid out with the half-depth shelf configuration. The half-depth adjustable shelf in 3/4 inch plywood keeps stored weight closer to the back, which reduces leverage on the wall fasteners and leaves more open access at the front. Bull-nosed, foil-covered front edges on that shelf create a smooth front edge that stands up to routine loading and unloading of items.
The cabinet sides, bottom, and back all use 1/2 inch plywood, so the interior surfaces handle typical cabinet loads across the full height and width. Vinyl-covered back panels on the interior introduce a wipe-friendly surface along the rear wall, which helps keep stored areas cleaner over time. All-wood 3/4 inch corner blocks at every corner contribute to the rigid feel of the cabinet box when it is loaded with contents. The front frame made from 3/4 inch solid maple wood provides a solid reference for door alignment and a robust edge for repeated door contact. Together, these details support use as a primary wall storage cabinet in kitchen or similar wall installations where consistent door action and interior access are important.
The face frame rails are pocket drilled and assembled with 1 1/4 inch screws, creating predictable and repeatable joints that hold alignment while the rest of the cabinet is fastened to the frame. The 1/2 inch dado used to seat the side panels and bottom into the front frame fixes their position during assembly, which improves squareness from cabinet to cabinet in a run. Gluing and stapling the 1/2 inch plywood sides and bottom into that dado further locks the geometry, so the cabinet maintains its shape when tension is applied at mounting points. Back panels of vinyl-covered 1/2 inch plywood are glued and nailed into their 1/2 inch dado and stapled to the hang rail and bottom, creating a continuous structural loop from front frame to back and down to the base.
All-wood 3/4 inch corner blocks installed at each corner add triangulation, which helps the cabinet stay rigid when it is clamped, lifted, and fastened on site. The self-locking 1/4 inch diameter clips supporting the 3/4 inch plywood shelf provide repeatable shelf positioning because the clip size and holes are consistent, which means shelf height changes do not disturb the cabinet structure. The bull-nosed, foil-covered front edge on the half-depth shelf presents a uniform edge that stands up to frequent contact, helping maintain a consistent interior appearance across multiple cabinets. Because the Brownstone Dartmouth cabinet fronts are 3/4 inch solid maple wood, door and face frame surfaces deliver a solid substrate for hardware across repeated units in a project.
The cabinet measures 42 inches wide, 12 inches deep, and 36 inches high, so it fits wall layouts designed around that footprint and aligns with common 36 inch wall cabinet installations.
The cabinet box uses 1/2 inch plywood sides, bottom, and back set in 1/2 inch dados, glued, stapled, and nailed, which creates a rigid structure for mounting and everyday storage loads.
The cabinet fronts are made from 3/4 inch solid maple wood, providing a strong face frame that supports hinge attachment and helps keep door alignment stable over time.
The half-depth adjustable 3/4 inch plywood shelf is held by self-locking 1/4 inch diameter clips on the sides, allowing position changes while keeping the shelf seated during regular use.
The half-depth shelf keeps stored weight closer to the wall and leaves more open space at the front of the cabinet, easing reach while reducing forward leverage on wall fasteners.
All-wood 3/4 inch corner blocks at all corners reinforce the cabinet box, so it stays more rigid during handling, mounting, and long-term loading with stored items.
This Wolf Dartmouth Brownstone Classic Series wall cabinet combines 3/4 inch solid maple fronts, 1/2 inch plywood box construction, and vinyl-covered plywood backs in a 42 inch by 12 inch by 36 inch format, so it fits standard wall runs needing framed construction. The pocket drilled rails fastened with 1 1/4 inch screws, glued and stapled 1/2 inch plywood sides and bottom in 1/2 inch dados, and all-wood 3/4 inch corner blocks produce a rigid cabinet ready for wall mounting. Two doors with a center stile, paired with an adjustable half-depth 3/4 inch plywood shelf on self-locking clips, give a practical interior layout that can be tuned to stored contents. Use this cabinet when a Dartmouth Brownstone framed wall unit with these exact dimensions and construction details is required.
Sold In: 1 Each