Sugatsune CHC-S Series cable grommet gives you a compact pass-through point for cables while keeping the hole in your material controlled and protected, which matters when routing wires through finished cabinetry or furniture panels.
This CHC-S Series part is identified as cable grommet type hardware, so it is intended to finish a drilled opening rather than leaving a raw bore, helping keep workpieces looking consistent on visible surfaces.
The product name specifies an 11/16 inch diameter cable grommet, so it is sized for small cable runs where you only need a modest opening, useful on tight layouts like narrow rails or compact multimedia furniture.
The same name calls out a zinc construction, so the body is metal-based rather than plastic, giving a firm edge around the hole that resists damage from routine cable movement in typical woodworking environments.
The description notes an antique brass finish, which means the visible trim can coordinate with other antique brass hardware on the installation, helping maintain a unified appearance across knobs, pulls, and grommets on the project.
The manufacturer part number CHC-S18DB ties this exact grommet to ordering systems, so installers can confidently reorder the same component across multiple jobs.
The product name specifies an 11/16 inch diameter cable grommet, which signals the overall footprint on the mounting surface and helps determine how much face area the trim will occupy on shelves, closets, or workspace panels.
The web description lists a bore diameter of 9/16 in, so the drilled hole is smaller than the outside diameter, providing a visible flange around the opening that can conceal slight chipping or variation at the cut edge.
This 9/16 in bore dimension directly guides the drilling step, allowing fabricators to select the correct bit size when preparing panels, while the 11/16 inch outer sizing informs layout when coordinating with adjacent hardware or edge distances.
The SAP description calls the part a split cable grommet, indicating that its function centers on creating a defined passage for wiring through a prepared bore, which is typical in multimedia and workspace components where cords must exit neatly.
Because the grommet is classified under shelf, closet, and garage organization as well as multimedia and workspace components, its diameters align with organizing light-duty cable runs in those environments.
The category listing connects this cable grommet to shelf, closet, and garage organization, so it suits storage systems where small electronics or lighting need a clean cable exit through panels or dividers.
The same category also places it under multimedia and workspace components, tying the part to desks, media consoles, and workstations where monitor cables, power leads, or peripheral wires pass through tops and backs.
The SAP description labels the product a split cable grommet, which aligns with applications that route cords through a hole rather than leaving bare wood or panel edges, helping maintain an orderly appearance on the finished installation.
The product class being grommets reinforces that its job is to line and finish a bore, so it belongs anywhere a drilled opening in wood or similar substrate carries cables from one side to the other in common woodworking assemblies.
The antique brass finish called out in the product name makes this grommet a natural fit in spaces using antique brass cabinet hardware, so designers can echo that metal tone on cable pass-through points across a room.
The compact 11/16 inch diameter referenced in the name allows it to function in narrower rails or small panels often found on furniture-grade media cabinets, helping keep cutouts proportionate to the scale of the piece.
The bore diameter of 9/16 in from the web description gives a passage sized for modest cable bundles typical of home offices or closet lighting, supporting runs where only a few conductors need to exit a compartment.
Since the grommet appears under both closet organization and multimedia components, using this same part across matching closets and office furniture can keep cable pass-through points visually consistent.
The web description specifies a bore diameter of 9/16 in, giving a precise drilling target that leads to repeatable hole sizing across multiple panels, which matters when producing sets of shelves or cabinets on a job.
The 11/16 inch diameter named in the product title defines the trim footprint, so installers can set consistent edge distances and spacing from adjacent hardware, improving alignment on long cabinet runs or workspace banks.
The zinc material called out in the SAP description and name provides a hard, stable ring around the bore, helping maintain a crisp circular opening when cables move during normal use over the life of the installation.
The antique brass finish in the product name gives a predictable color and sheen, so fabricators can confidently specify this part wherever that metal tone is part of the design intent, keeping finishes aligned from drawing to finished room.
The listing under multimedia and workspace components signals that the 9/16 in bore size is oriented toward typical data or power cords used at desks and media centers, supporting consistent routing solutions in those environments.
The manufacturer part number CHC-S18DB uniquely identifies this exact configuration, which simplifies repeat ordering for multi-phase projects where the same cable grommet specification must be carried forward.
The product class of grommets and the description as a split cable grommet together emphasize that it is purpose-built for cable pass-through in woodworking and related assemblies, helping standardize how openings are treated wherever wires exit cabinets.
The association with shelf, closet, and garage organization indicates that this dimensional combination works with typical panel thicknesses in storage systems, supporting uniform hole treatment across different storage zones that share a design language.
The Sugatsune CHC-S Series cable grommet is described as 11/16 inch diameter, so its trim ring occupies a compact footprint on cabinet or furniture surfaces.
The CHC-S18DB cable grommet has a listed bore diameter of 9/16 in, guiding the drill size used to prepare panels for a proper fit.
The SPLIT CABLE GROMMET, ZINC, 11/16'DIA, AB description states zinc, so the grommet body is metal-based for a firm edge around the opening.
The product name notes an antique brass finish, so the visible surface presents a warm brass tone that coordinates with antique brass hardware.
The category lists shelf, closet, and garage organization plus multimedia and workspace components, aligning it with storage systems, desks, and media furniture.
The manufacturer part number CHC-S18DB identifies this specific Sugatsune CHC-S Series split cable grommet configuration for ordering and repeat use.
The Sugatsune CHC-S Series cable grommet combines an 11/16 inch diameter body with a 9/16 in bore diameter, giving tradespeople a defined relationship between trim size and drilled opening on cabinetry and furniture work.
Its zinc construction with antique brass finish ties functional cable routing to a specific metal tone, so projects using antique brass hardware can carry that look through to their cable pass-through points.
With its classification as a split cable grommet in multimedia, workspace, and storage-related categories, this CHC-S18DB part suits organized cable runs anywhere those environments rely on drilled panel openings.