Wood veneer edgebanding alder describes this FormWood edge banding that covers and finishes exposed board edges with a real alder veneer face. The 0.022 inch thickness gives a low-profile edge that blends smoothly with typical panel surfaces, helping finished parts look consistent along every edge. The 7/8 inch width provides coverage for common panel thicknesses with trim margin, so installers can flush trim back to the face for a clean line. A 500 foot roll length supports longer runs or multiple cabinet pieces without frequent changeover, which can help keep shop workflow moving. The fleece non-glued construction means the backing is prepared for a separate adhesive process, allowing shops to match this alder banding to their existing edgebanding equipment and glue choices. The alder species gives a wood surface that can be worked along with alder-faced panels in woodworking projects.
This FormWood wood veneer edgebanding, alder, 0.022 inch thick in 7/8 inch width, pairs well with standard edgebanding processes that apply adhesive to a non-glued backing. The fleece backing works with glue application systems that bond the banding to board edges in a single pass, supporting efficient production. The 7/8 inch width gives coverage on typical panel edges while leaving enough excess for trimming operations, so installers can trim back to a precise profile. The 0.022 inch thickness helps the edge transition stay modest, which matters when sanding and finishing alder-faced components to a consistent surface.
The FormWood NGALD7/8 alder edge banding is a wood veneer edgebanding designed for covering exposed edges in woodworking applications. The 7/8 inch width works on many panel thicknesses used in cabinetry and casework, giving installers room to align and trim the alder veneer to the face. The 500 foot roll format suits shops that run multiple pieces or repeated cabinet parts, because one roll supports extended runs. The alder veneer face matches alder projects where a consistent species is desired from face panel to edge, allowing finished components to present a unified alder appearance. The edge banding format keeps the alder surface available specifically at the edges of panels where core material would otherwise be visible.
This wood veneer edgebanding alder product uses a 0.022 inch thickness to keep the edge profile modest, which aids in sanding and finishing when aligning the banded edge with alder-faced panels. The fleece non-glued backing is intended for systems that apply adhesive during installation, so the same NGALD7/8 roll can integrate into a shop process that controls glue application, temperature, and feed speed. The 7/8 inch width provides working tolerance for positioning on the board edge and trimming back to final dimension, helping maintain straight, chip-free edges. With a 500 foot roll length, the edge banding supports repeated setups where the same alder banding is used across many components, reducing changes in appearance from one piece to the next. The FormWood brand ties this NGALD7/8 edgebanding to a defined product identity, simplifying reorders for ongoing alder projects that rely on consistent edging material.
The wood veneer edgebanding, alder, is supplied as a 7/8 inch wide, 0.022 inch thick, 500 foot roll, which supports extended edging runs and trimming margin on typical panel edges.
The fleece non-glued alder edgebanding uses a fleece backing without pre-applied adhesive, so it is intended for use with separate glue application during the edgebanding process.
This FormWood edge banding uses an alder wood veneer face, allowing edges to visually coordinate with alder components in woodworking projects that use the same species.
The 0.022 inch thick alder edgebanding creates a modest edge profile, which supports a smoother transition between panel face and edge after trimming and finishing.
The NGALD7/8 manufacturer part number identifies this specific FormWood alder wood veneer edgebanding in 0.022 inch thickness, 7/8 inch width, and 500 foot roll format.
The 7/8 inch width gives coverage beyond the panel edge, so installers can trim the alder banding back to the panel surface for a precise, straight finished edge.
The FormWood wood veneer edgebanding, alder, 0.022 inch thick in a 7/8 inch by 500 foot roll, provides a defined alder edge material for woodworking projects. The fleece non-glued backing aligns with shop processes that apply adhesive separately, and the roll format supports multiple parts and repeat work. For projects calling for alder-faced edges on exposed boards, choosing this NGALD7/8 edgebanding gives a consistent species and dimension across runs.
Sold In: 1 Roll