FormWood Clear Alder Wood Veneer Edgebanding 7/8", Pre Glued, Unfinished, 250', PGALD7/8

Wood Veneer Edgebanding Pre-Glued Alder For Clean Edges

Wood veneer edgebanding pre-glued alder gives cabinet and furniture projects a real-wood alder edge that visually matches alder surfaces, so exposed plywood or composite cores disappear and finished parts look consistent across the run. This FormWood edge banding is classified as wood edgebanding and edge banding, so it fits straight into woodworking and surfacing workflows where a wood veneer edge is required. The alder veneer construction creates an alder face at the edge, which supports jobs that call for alder fronts or trim. A 0.034 inch thickness provides a veneer layer with substance for machining and finishing, while still behaving like standard wood edgebanding during normal shop handling and trimming. The 7/8 inch width covers common panel thicknesses in cabinet work with room for slight overhang, which simplifies flush-trimming and helps achieve a clean, straight finished edge from end to end.

Key Alder Edgebanding Details That Help Jobs

• This wood veneer edgebanding, pre-glued, alder design combines alder face material with a pre-applied adhesive layer, so installers can apply heat-activated bonding without separate glue steps and keep the workflow focused on cutting, banding, and trimming.
• The 0.034 inch thick construction creates a veneer layer with enough body for typical edge machining and finishing while still acting like standard wood edgebanding, which supports clean trimming passes and predictable edge profiling on cabinets and fixtures.
• The 7/8 inch width gives coverage for standard casework panel thicknesses with slight overhang, so the band can be centered over the substrate and then trimmed back to flush, reducing visible core exposure and simplifying alignment along the length of each part.
• The 250 foot roll format provides a continuous run of alder edge material for multiple parts or larger jobs, which supports consistent color and grain direction around doors, drawer fronts, or cabinet sides taken from the same roll segment.
• The FormWood brand and PGALD7/8 manufacturer part number identify this specific alder wood veneer edge banding in the 7/8 inch pre-glued format, which helps shops repeat successful jobs by reordering the same roll specification for follow-up work.

Edgebanding Size And Glue Layer For Installation

This wood veneer edgebanding, pre-glued, alder roll uses a pre-glued adhesive layer on the back of the veneer, so heat-activated application becomes a single-pass operation where the installer focuses on pressure and tracking along the panel edge. The 0.034 inch thick veneer builds a modest edge profile, which fits easily under standard edge trimmers and flush-trim bits during cleanup. With a 7/8 inch width, the band overhangs typical 3/4 inch casework material, giving room for trimming without risking a short edge. The 250 foot roll length supports setting up repeated pieces at one machine without frequent changeovers, which suits runs of cabinet components or shelving where the same alder edge is required throughout.

Using FormWood Alder Edgebanding In Woodwork

Where This Alder Veneer Edgebanding Fits Best

FormWood wood veneer edgebanding, pre-glued, alder fits woodworking and surfacing projects that use alder as a visible species on faces or trims, because the alder veneer presents a matching wood edge along exposed sides. In cabinet shops, the 7/8 inch width suits edging for panels near typical 3/4 inch thickness, allowing slight overhang for trimming on cabinet boxes, shelves, or end panels. In furniture or fixture work, the 0.034 inch thickness supports edging for components that may need light profiling or sanding, while still acting like conventional veneer banding during machining. The 250 foot roll length fits workflows that process multiple doors, drawer fronts, or case components in series, allowing the same alder look to carry around each opening and across grouped pieces in a project.

Why These Edgebanding Details Support Consistent Results

FormWood wood veneer edgebanding, pre-glued, alder pairs its pre-glued backing with a continuous 250 foot roll, so once application settings are dialed in, the installer can run multiple parts with the same pressure and speed, helping keep bond lines uniform. The 7/8 inch size gives predictable overhang on common panel thicknesses, which reduces time spent fine-positioning the band and supports repeatable alignment from part to part. With a 0.034 inch thick veneer face, the alder surface accepts standard sanding and finishing steps used on other wood edgebanding, so the edge can move through the same finishing line as adjacent alder components. The manufacturer part number PGALD7/8 directly tags this combination of species, pre-glued construction, width, and roll length, which simplifies pulling the correct alder edgebanding from inventory when matching previous work or standard shop specifications.

Common Questions About PGALD7/8 Alder Edgebanding

Select FormWood Alder Edgebanding For Matching Edges

This wood veneer edgebanding, pre-glued, alder from FormWood provides a 0.034 inch thick alder face in a 7/8 inch x 250 foot roll, giving shops a repeatable alder edge solution for casework and furniture components. The pre-glued construction lets installers rely on a single-pass, heat-activated application method, while the width and thickness support standard trimming and finishing steps already in place. For projects built around alder surfaces that need a consistent alder edge, selecting the PGALD7/8 alder edgebanding aligns the roll specification with the material and dimensions used throughout the job.