CLOSET ROD FLANGES from Knape and Vogt give you a dedicated mounting point for supporting a closet rod, so the load goes into the wall or panel instead of stressing the rod ends. This KV Closet-PRO HD flange pair is made of steel, which provides a rigid bearing surface at each end of the rod for consistent support under everyday hanging loads. The pair configuration uses one open flange and one closed flange, letting you drop the rod into the open end and capture it firmly in the closed end during installation. The bronze finish gives the flanges a finished appearance that blends with bronze closet hardware, which helps keep exposed fittings visually consistent on built-ins or reach-in runs.
This Knape and Vogt KV Closet-PRO HD flange pair is sized for 1-5/16 inch diameter closet rods, so the cup of each flange matches that profile and helps keep the rod from shifting during use. The open and closed flange combination sets up a fixed end and a drop-in end, which simplifies positioning the rod between opposing walls or panels before final fastening. Color-matched mounting hardware is identified in the product description, so fastener heads visually match the bronze finish when securing each flange to a vertical surface.
The Knape and Vogt KV Closet-PRO HD flange pair is part of the closet shelf and rod brackets class, so it is used at the ends of a closet rod in shelf and rod installations. Because the flanges are made of steel, they are suited to typical indoor closet environments where metal hardware is used to carry hanging garments on a 1-5/16 inch diameter rod. The open flange in the pair is positioned where the rod needs to be dropped in from above or the front, which helps when setting a rod between two fixed panels or walls with limited clearance. The matching closed flange at the other end fully surrounds the rod, so that end is positively captured once the rod is set in place.
The 1-5/16 inch diameter design directly matches common heavy-duty closet rods, so the rod nests correctly in both the open and closed flanges and keeps the hanging line straight along the run. The steel construction gives the flanges a firm seat and resists deformation at the rod contact points, which helps maintain alignment of the rod ends after the closet has been loaded with garments. The bronze color allows the flanges to visually match bronze-colored closet components, so the supporting hardware does not stand out against coordinated rods and brackets. Using one open and one closed flange in each KV Closet-PRO HD flange pair creates a repeatable layout: the closed flange sets a fixed bearing point while the open flange lets you place the rod accurately before tightening fasteners for the final position.
The KV Closet-PRO HD flange pair is designed for 1-5/16 inch diameter closet rods, so rods with that diameter seat properly and stay centered in the flange cups.
The closet rod flanges are made of steel, so the rod ends bear on a rigid metal surface that supports typical hanging loads in closet installations.
The KV Closet-PRO HD flange pair provides one open flange to drop the rod into position and one closed flange to fully capture the opposite end for a secure bearing point.
The CD-0010-BRZ flanges have a bronze color, so they visually coordinate with bronze closet rods and other bronze-finished closet components.
The Knape and Vogt CD-0010-BRZ flange pair is in the closet shelf and rod brackets class, so it is intended for supporting closet rods in shelf and rod systems.
The CD-0010-BRZ part number identifies this Knape and Vogt KV Closet-PRO HD bronze flange pair, helping match it with 1-5/16 inch closet rods in project planning.
The Knape and Vogt KV Closet-PRO HD flange pair centers on a steel construction, a 1-5/16 inch rod diameter fit, and a bronze color, so it aligns well with heavy-duty bronze closet layouts using that specific rod size. The one open and one closed flange arrangement helps establish a consistent rod layout between walls or panels, while the closet shelf and rod brackets classification ties it directly to hanging and shelf systems. For projects using 1-5/16 inch diameter closet rods in bronze, this CD-0010-BRZ flange pair provides a clearly defined bearing point at each rod end.
Sold In: 1 Box