Knape And Vogt 26 Inch Drawer Slides For Full Travel

Knape and Vogt 26 inch drawer slides use the KV Model 8417 design to give a full extension slide, so a 26 inch drawer can be pulled out to access its stored contents along the entire length of the drawer box. The side mount layout positions each slide on the cabinet side wall, which leaves the drawer bottom clear and supports common cabinet construction methods in shops and on job sites. The ball bearing mechanism in these slides provides smooth drawer movement along the travel path, which helps drawers open and close consistently under normal cabinet use. The self closing feature on the KV Model 8417 draws the slide to the closed position once the drawer reaches the active zone, which reduces the chance of a drawer sitting slightly open after use. The unhanded design lets one slide serve either left or right side, which simplifies layout and reduces part sorting during installation.

Key Working Details Of KV 8417 Drawer Slides

• The full extension design allows the drawer to travel the full slide length, which lets users reach stored items along the entire drawer without leaving a hidden section at the back.
• The self closing feature draws the slide into the closed position, which helps keep drawer fronts aligned with the cabinet face when the drawer is pushed near closed in everyday use.
• The unhanded side mount configuration means each slide can be used on either side of the drawer, which streamlines installation and reduces the need to track left and right specific parts.
• The zinc finish on these slides provides a uniform coated surface, which supports normal cabinet environments where a standard plated slide is preferred over a raw steel component.
• The ball bearing construction supports the moving members of the slide, which helps the drawer open and close with a controlled motion along the length of travel.

Side Mount Fit, Clearances, And Fastener Setup

The KV Model 8417 slide in 26 inch length is a side mount drawer slide, so it fits between the cabinet side and the drawer side. The specified side clearance for this model is 1/2 inch plus 1/32 inch, minus 0 inch on each side, which defines the working gap between drawer side and cabinet side wall for proper running clearance. The slide height is 1-13/16 inch, so the drawer side design and cabinet opening height can be laid out to accommodate that slide profile while keeping the desired drawer box proportions. The 32mm pattern on this slide aligns with 32mm system boring layouts, which helps position mounting screws on cabinets built around that system. Recommended fasteners are #7 x 5/8 inch Phillips pan head, which match the slide holes and support typical cabinet side materials.

Using 8417P 26 Slides In Cabinet Construction

Where KV 8417 Side Mount Slides Fit Best

The Knape and Vogt 26 inch drawer slides in the 8417P 26 version are part of the Side Mount Drawer Slides class, so they fit cabinets designed for side mount ball bearing hardware rather than bottom mount or center mount layouts. The specified side clearance of 1/2 inch plus 1/32 inch, minus 0 inch on each side ties directly into drawer box sizing, which lets the builder size drawer widths so the slides run smoothly without racking. The slide height of 1-13/16 inch works within common drawer side heights, which allows the installer to position the slides to carry the drawer without interfering with the drawer bottom or top rails. Because the slide uses a 32mm pattern, it aligns with cabinets bored to the 32mm system, which lets installers use existing line boring for consistent mounting positions across a run of cabinets.

Why These KV 8417 Details Support Repeatable Results

The full extension action on the 8417P 26 slide allows the cabinet maker to promise full drawer access, which is important when deep drawers are used for storage and users expect to reach the back. The self closing feature that draws the slide to the closed position helps keep drawer fronts in a uniform plane, which supports clean visual alignment on banks of drawers without repeated manual adjustment by the end user. The unhanded design means one part number can be stocked for both sides, which simplifies inventory on service trucks and in shops and reduces assembly errors from mixing left and right specific pieces. The 32mm pattern provides predictable screw locations relative to the cabinet edge, which supports jigs and boring patterns already set up around the 32mm system. Recommended #7 x 5/8 inch Phillips pan head fasteners match both the slide holes and typical cabinet side thickness, which helps the slide seat firmly without breaking through the opposite face of the cabinet material.

Common Questions About 26 Inch KV 8417 Slides

Select KV 8417P 26 Slides For Precise Drawer Travel

The Knape and Vogt 26 inch drawer slides in the 8417P 26 model combine side mount ball bearing construction, full extension travel, and a self closing feature, so they support drawers that open fully and return to the closed position with consistent motion. The specified 1/2 inch plus 1/32 inch, minus 0 inch side clearance and 1-13/16 inch height give clear layout targets when sizing drawer boxes for new cabinets or fitting replacement slides in existing casework. The 32mm pattern and recommended #7 x 5/8 inch Phillips pan head fasteners align with standard cabinet building practices, so these slides fit well into production shops and site installations.