KV8419 16" Over Travel Self-Close Ball Bearing Drawer Slides, Unhanded Side Mount Zinc Bulk-Pack - 8419B 16

Knape And Vogt 16 Inch Over Travel Self Close Drawer Slides

Knape and Vogt 16 inch over travel self close drawer slides provide ball bearing performance with 1 inch overtravel, so drawers can open beyond the cabinet face for easier access to stored items during everyday use or service work. The self closing function built into this 8419 Series slide draws the drawer closed at the end of travel, which helps bring the drawer back to position consistently. The side mount design matches common cabinet construction, allowing the slide to mount along the cabinet side instead of under the drawer. An unhanded configuration means the same slide works on either side of the drawer, which simplifies ordering and layout on the bench. The zinc finish on the slide presents a clean, bright appearance that matches typical cabinet hardware components in many shops.

Key 8419B 16 Drawer Slide Details For Projects

• The 1 inch overtravel lets the drawer extend past the face of the cabinet, which can expose the full drawer box for loading and unloading without needing to reach around the face frame.
• The self closing feature engages near the end of travel to pull the drawer shut, which can help seat the drawer consistently against the front and support uniform reveals across a run.
• The recommended side clearance of 1/2 inch plus 1/32 inch minus 0 inch on each side guides drawer box sizing, which supports smoother operation by keeping the ball bearings running in line with the slide members.
• The 1-13/16 inch height of the slide sets the vertical space required on the drawer side, which helps in planning notch depths, side heights, and clearances around shelves or roll-outs.
• The 32 mm pattern gives a hole layout that aligns with 32 mm system drilling, which can speed installation in shops already using line boring equipment.
• The Anochromek finish provides a defined surface treatment on the steel members, which supports a uniform look across multiple slides in the same installation.

Side Mount Installation And Fit Details For 8419 Slides

The 8419 Series uses a side mount configuration, so the cabinet member fastens directly to the cabinet side while the drawer member fastens to the drawer side, creating a familiar layout for many cabinetry builds. The specified side clearance of 1/2 inch plus 1/32 inch minus 0 inch per side directs the exact drawer width relative to the cabinet opening, which helps the ball bearing members run square under load. A slide height of 1-13/16 inch defines how much vertical surface is needed along each drawer side, supporting decisions on drawer side height and any necessary bottom or side notching. The recommended #7 x 1/2 inch Phillips pan head fasteners give a concrete fastening option that matches the hole sizes in the slide members, supporting a secure mount into cabinet sides and drawer boxes.

Using KV 8419B 16 Slides In Cabinet Builds

Where These 16 Inch Overtravel Slides Fit Best

The KV Model 8419 in the 16 inch length works where a 16 inch slide travel is suited to the cabinet depth, aligning the drawer box size with standard kitchen, bath, or shop cabinet layouts that accept this length. The 1 inch overtravel allows the drawer to extend slightly beyond its nominal length, so even when the cabinet front projects, the drawer back can clear the face for better visibility into the rear section. Side mount installation supports use in cases with solid cabinet sides, where attaching a full-height slide member along the sidewall is practical and common. The 1-13/16 inch slide height coordinates with typical drawer side dimensions, so the slide can sit low enough to support the drawer bottom while leaving room above for sides or applied tops. The unhanded design means the same 8419B 16 unit can be used on either the left or right side, which can reduce part differentiation on carts or in inventory during production runs.

Details That Support Repeatable Drawer Slide Results

The self closing feature of the 8419 Series contributes to more consistent drawer positioning when multiple drawers share a common face alignment, because the mechanism draws the drawer to the same point at the end of each cycle. The 32 mm pattern on the slide members ties the mounting holes to a standard system layout, which allows installers using 32 mm line boring to place holes accurately and repeat the same position across many cabinets. Following the side clearance of 1/2 inch plus 1/32 inch minus 0 inch per side keeps the drawer box centered within the slide travel, which can reduce side loading on the ball bearings during operation. The ball bearing construction distributes movement along rolling elements, which supports smoother travel compared to simple friction runners when drawers are opened and closed repeatedly. The zinc and Anochromek finishes on the slide surfaces provide a defined coating across the steel, which helps maintain a uniform appearance along the drawer bank and pairs visually with other zinc finished hardware in the project.

Common Questions About KV 8419B 16 Drawer Slides

Selecting KV 8419B 16 Slides For Your Next Run

The Knape and Vogt 16 inch over travel self close drawer slides in the 8419B 16 model combine side mount installation, ball bearing movement, and self closing action in a single slide, supporting consistent drawer performance across cabinets. With defined side clearance, slide height, 32 mm pattern, and zinc Anochromek finish, these slides give clear parameters for sizing drawer boxes and drilling patterns. For projects matching a 16 inch side mount ball bearing slide with 1 inch overtravel and self closing behavior, this 8419 Series option from Wurth Baer Supply aligns well with production-focused cabinet work.