Knape And Vogt 12 Inch Drawer Slides For Work Surfaces

Knape and Vogt 12 inch drawer slides use the 8414 Series hold-out design so a work surface stays extended when pulled out, which keeps a pull-out shelf or platform from drifting back during use. The full extension action brings the connected surface completely out to its working position, giving full access across the 12 inch travel instead of leaving part of the surface recessed. The side mount, ball bearing construction supports smooth movement along the cabinet side, which helps the slide operate consistently on repeat openings. The unhanded design lets this 8414P 12 slide mount on either side without separate left or right parts, simplifying layout and part selection in the shop. The zinc finish on the slide components provides a clean metallic appearance that suits typical cabinet interiors and built-ins.

Key 8414P 12 Slide Details For Installers

• The 12 inch length sets the pull-out travel, so the connected work surface or drawer uses a compact slide suited to shallow cabinets or shorter platforms while still gaining full extension over that distance.
• The hold-out feature for work surfaces locks the slide in its extended position, so a pull-out top, keyboard tray, or auxiliary work shelf stays in place under load instead of sliding back as it is used.
• The side clearance of 1/2 inch plus 1/32 inch minus 0 inch on each side defines the cabinet opening needed, giving a clear target for carcass width so the slide runs freely without side bind.
• The slide height of 1-13/16 inch sets the vertical space the member occupies, which helps in stacking multiple slides or fitting above clearances such as face-frame rails and stretchers.
• The 32mm pattern designation means the slide works with 32mm system hole layouts, which streamlines boring operations in panel processing and aligns the slide with standard cabinet line drilling.
• The recommended fasteners of #7 x 5/8 inch Phillips pan head give a specific screw size and head style, helping achieve solid mounting in typical cabinet materials without over-penetrating thin panels.

Side Mount, Clearance, And Mounting Details

This 8414 Series slide is built as a side mount, so it attaches to the cabinet side and the drawer or work surface member using the 32mm pattern, which fits common system-bored panels. The specified side clearance of 1/2 inch plus 1/32 inch minus 0 inch on each side sets the total gap between the drawer or pull-out and the cabinet interior, allowing the ball bearing members to glide without rubbing the case. With a slide height of 1-13/16 inch, the installer can position it to clear adjacent hardware or shelves, maintaining smooth travel even in tight vertical spaces. Using the recommended #7 x 5/8 inch Phillips pan head fasteners keeps the slide anchored along its length so the hold-out action and full extension performance stay consistent over repeated cycles.

Using KV 8414 Hold Out Slides In Projects

Where This 12 Inch Drawer Slide Works Best

The KV Model 8414 hold-out slide is designed to lock and maintain work surfaces in an extended open position, so it suits pull-out work tops, equipment shelves, or task drawers that must stay deployed while in use. Its full extension travel over 12 inches lets the platform or drawer clear the cabinet face, giving access to the entire surface rather than leaving a portion recessed inside the case. In cabinets built on the 32mm system, the 32mm pattern on this slide aligns with pre-bored rows, integrating easily into frameless cabinetry and modular fixtures. The side mount configuration matches cabinet constructions where the slide fastens directly to interior gables, supporting applications such as pull-out shelves, small workstations, or utility drawers that benefit from controlled, smooth travel. Because the slide is unhanded, it can be installed on either side of the pull-out, which simplifies jobsite layout and reduces the need to carry separate handed components.

How 8414P 12 Details Support Repeatable Results

The specified side clearance of 1/2 inch plus 1/32 inch minus 0 inch on each side helps achieve consistent fit across a run of cabinets, because the same opening formula applies to every pull-out using this model. The height of 1-13/16 inch gives a predictable envelope for planning vertical spacing, which is useful when stacking multiple work surfaces or combining this slide with other hardware in the same cabinet bay. The hold-out feature for work surfaces allows the extended position to stay fixed, supporting steady tool use or writing tasks without the platform drifting. Full extension lets the ball bearing members travel completely, improving usability when access to the rear of the shelf or drawer is important. The zinc finish on the slide components provides a neutral, metallic look that coordinates with typical cabinet interiors, and supports a professional appearance when the hardware is visible. The recommended #7 x 5/8 inch Phillips pan head fasteners provide a consistent mounting method, helping maintain alignment along the slide length and supporting stable operation over repeated openings and closings.

Common Questions About KV 8414P 12 Drawer Slides

Selecting The Right 12 Inch Full Extension Slide

The Knape and Vogt 12 inch drawer slides in the 8414 Series pair full extension movement with a hold-out feature for work surfaces, so they suit pull-outs that must stay open while being used. With defined side clearance of 1/2 inch plus 1/32 inch minus 0 inch on each side and a slide height of 1-13/16 inch, they provide clear dimensional targets for cabinet openings and vertical spacing. The 32mm pattern and unhanded side mount design align well with system-bored cabinetry and straightforward left or right installation. Using the recommended #7 x 5/8 inch Phillips pan head fasteners, installers can set up a pull-out that travels smoothly to its full 12 inch extension and maintains position in service.