Hickory Hardware Zephyr Series pull is a zinc die cast cabinet pull in a satin nickel finish with a 3 inch center to center hole spacing, so it serves as a straightforward handle option for many cabinet and drawer layouts using that standard measurement. The Belwith Keeler branding and Zephyr Series designation identify it as part of a coordinated decorative hardware line, which helps maintain a consistent look across multiple doors and drawers on the same job. The zinc die cast construction gives the pull a solid metal body, which supports repeated daily use when opening and closing cabinets in kitchens, baths, or shop storage. The satin nickel finish provides a muted metal appearance, which fits projects calling for a softer, brushed look rather than bright polished metal, helping it blend with common satin nickel hinges and other trim.
This 3 inch center to center pull uses two mounting points spaced 3 inches apart, which aligns with many factory-bored and jig-drilled cabinet fronts set up for that standard dimension. With a length of 3-13/16 inches, the body of the pull slightly overhangs beyond the hole pattern, giving visual balance on the front of the door while still leaving edge clearances for adjacent doors. The 1-1/8 inch projection sets the gripping surface off the face enough for a full finger pull, which is helpful on thicker drawer fronts where shallow pulls can be harder to grasp. A width of 13/16 inch keeps the profile compact, so installers can use it on narrower rails or small drawers while maintaining clearance between neighboring pulls in tight layouts.
The P2280-SN satin nickel pull from the Zephyr Series is suited to cabinet and drawer applications using a 3 inch center to center hole pattern, so it works wherever that spacing has been drilled into wood or composite fronts. Its satin nickel finish visually aligns with satin nickel hinges, slides with visible fronts, and other trim using similar tones, which keeps a run of cabinets looking consistent across doors and banked drawers. The 3-13/16 inch overall length lets it sit cleanly on standard face frame and frameless cabinet doors without crowding panel details, while still offering enough bar length for a comfortable hand grip on wider drawers. Because the width is 13/16 inch, it occupies a modest footprint on the rail, which helps on narrower drawer fronts, small vanity doors, or upper cabinets where space between pulls can be tight.
The 3 inch center to center dimension simplifies layout with common drilling jigs, which reduces layout variation from door to door and supports straight, repeatable hardware runs across a full kitchen or bank of casework. Using the specified 8-32 x 1 inch screw size keeps threading consistent with a standard cabinet fastener size, so installers can rely on known torque and thread engagement in typical door and drawer thicknesses. The 1-1/8 inch projection creates predictable hand clearance off the front surface, which matters when aligning pulls above countertop edges or near appliance panels where extra depth could cause interference. With a 3-13/16 inch length tied to the 3 inch hole spacing, hole positions stay away from door edges, supporting cleaner drilling and reducing risk of blowout near the stile edge. The 13/16 inch width maintains a balanced look relative to common stile widths, so aligning multiple pulls along a row of doors produces an even visual line.
The P2280-SN pull serves cabinet and drawer fronts with a 3 inch center to center pattern, so it suits many kitchen, bath, or storage layouts drilled on that standard spacing.
The zinc die cast construction gives the pull a solid metal body, so it handles repeated opening and closing on frequently used cabinet doors and drawers.
The satin nickel finish provides a muted metallic look, which pairs well with other satin nickel cabinet hardware for a coordinated appearance across a project.
The 3 inch center to center dimension sets the distance between mounting holes, aligning with many pre-drilled cabinet fronts and standard drilling jigs.
The 3-13/16 inch length and 1-1/8 inch projection provide enough bar length and depth so fingers can grasp the pull comfortably without crowding the cabinet face.
The 8-32 x 1 inch screw size matches a common cabinet fastener standard, supporting predictable threading into typical door and drawer thicknesses.
The Hickory Hardware Zephyr Series pull in satin nickel, model P2280-SN, combines a 3 inch center to center layout with a 3-13/16 inch length, 1-1/8 inch projection, and 13/16 inch width, giving cabinet builders a well-defined set of dimensions to work into drilling setups. With zinc die cast construction and a satin nickel finish aligned to common cabinet hardware tones, it fits projects that call for consistent appearance and repeatable mounting across multiple doors and drawers. For cabinet runs laid out on a 3 inch center to center pattern, this Belwith Keeler pull offers a clear, dimensioned option ready to integrate into shop drawings and on-site installs.
Sold In: 1 Each
