Wurth flat head assembly screw describes a case hardened #8 x 1-1/4 inch screw designed for assembly work, so installers get a fastener built to handle typical cabinet and woodworking connections. The screw uses a flat head, which sits flush in countersunk holes, keeping hinge plates, brackets, or hardware tight against the material. The coarse thread is specified in the description, so it bites aggressively into wood-based substrates, helping pull joints together during assembly. The point is described as sharp, so the screw starts quickly into material and drives with less wandering. The screw is lubricated, as stated, which reduces driving friction and supports smoother insertion under a drill or driver. The product is identified as an assembly screw in the description, indicating its role where repeatable, consistent fastening is needed in production or onsite work.
The web description specifies that the screw uses #2 Square Drive bits to insert, giving a positive bit engagement that supports firm driving in assembly situations. It also states that #2 Phillips Drive bits can be used for after market adjustment, so existing installations can be snugged or reset with a commonly carried bit. Length information notes that 3/4 inch and 1 inch screws in this product line are fully threaded, while other sizes are threaded two-thirds from the bottom, which clarifies how thread coverage changes by length. This #8 x 1-1/4 inch screw follows that pattern, so the upper shank section above the lower two-thirds remains unthreaded, which can help pull pieces tightly together when driving through one component into another.
The category is listed as Fasteners and Screws, and the web description calls this an assembly screw, positioning it for cabinet and woodworking assembly tasks where repeatable fastening is needed. The sharp point and coarse thread combination supports use in wood-based materials where quick starting and strong holding are valuable, such as joining panels or fastening hardware plates. The flat head layout means it works where countersunk holes are prepared, allowing the head to sink and clamp hardware or joint faces evenly. Because the screw is case hardened, as described, it suits applications that involve powered driving with consistent torque, typical of production shops or serious installation work.
The specified combo of #2 Square Drive for primary insertion and optional #2 Phillips Drive for after market adjustment gives flexibility on site, since installers can use square bits for original construction and rely on Phillips bits for follow-up service. The mention that only 3/4 inch and 1 inch sizes are fully threaded, while longer sizes are threaded two-thirds from the bottom, explains that this 1-1/4 inch screw has a partially unthreaded upper shank, which helps pull the top piece tight to the substrate while the threads grip below. Lubrication described in the product details reduces driving resistance, which is helpful when setting many screws during cabinet or fixture assembly. The case hardened description means the screw is prepared for these repetitive driving loads, supporting consistent performance during runs of similar joints.
This product is listed as a Wurth #8 x 1-1/4 inch flat head assembly screw, so it fits applications calling for that specific diameter and length.
The description states that lengths other than 3/4 inch and 1 inch are threaded two-thirds from the bottom, so the 1-1/4 inch screw has a partially unthreaded upper shank.
The web description states it uses #2 Square Drive bits for insertion, providing positive engagement for powered or manual driving.
The description notes that #2 Phillips Drive bits can be used for after market adjustment, which helps when servicing or tightening existing installations.
The product description lists the screw as case hardened, which prepares it for the typical torque and driving demands in assembly and installation work.
The screw is described as lubricated, which reduces friction during driving and supports smoother seating into wood-based materials.
This Wurth #8 x 1-1/4 inch flat head assembly screw combines a case hardened body, lubricated coarse threads, and a sharp point to support efficient fastening in wood-based assemblies. The specified drive system uses #2 Square Drive bits for primary installation and allows #2 Phillips Drive bits for after market adjustment, so one screw type serves both initial build and later service work. When a project calls for this thread pattern, drive style, and length, choosing this screw matches the listed characteristics to the assembly requirements.
Sold In: 1000 Each
