Wurth #8 x 3 washer head screw gives you a round washerhead that spreads load in soft woods, which helps keep the head from sinking into the wood during assembly. The screw uses a patented serrated tooth turbo thread that allows for quick starting in the material, so you get faster driving at the bench or on the job. That same turbo thread design reduces splitting in the wood, which protects parts you already machined and finished. Reduced drive torque from the thread geometry means less strain on drivers over a long run of installations. This screw is case hardened and lubricated, so it is built for driving into wood while limiting friction as it seats. It is used in woodworking applications such as assembly, face frames, slides, hinges, and hardware, which keeps one screw style working across common cabinet tasks.
This washer head assembly screw uses #2 square drive bits to insert, which gives a positive bit-to-head engagement during driving. #2 Phillips drive bits can be used for aftermarket adjustment, so installed screws can be tuned later without swapping to a square bit. The sharp point and patented serrated tooth turbo thread allow for quick starting in wood, reducing the time needed to pick up a thread. Reduced splitting from the turbo thread helps protect face frames, narrow parts, and hinge areas when you run screws near an edge. Reduced drive torque from the thread geometry also eases work with powered drivers on larger runs of assembly.
The round washerhead on this #8 x 3 screw is typically used in soft woods to prevent the head from sinking into the wood, which is useful on cabinet sides and stretchers where overdriving could dish the surface. In woodworking applications such as assembly, face frames, slides, hinges, and hardware, the washerhead helps clamp fittings evenly across the bearing surface. The sharp point works with the patented serrated tooth turbo thread to start quickly in soft woods, so you can place screws efficiently along rails, cleats, and brackets. Because the screw is case hardened and lubricated, it is suited to repeated driving into wood during cabinet and furniture builds. Length options where 3/4 inch and 1 inch are threaded fully, and other sizes are threaded 2/3's from the bottom, give different holding behavior for various build details.
The patented serrated tooth turbo thread allows for quick starting, reduced splitting, and less drive torque, which helps keep workpieces intact when you fasten close to corners or along narrow frame members. Reduced splitting means less rework on parts that already carry joinery or finish. Less drive torque from the turbo thread design makes it easier on drivers and helps maintain bit control during long runs of fasteners. The combination of #2 square drive bits for insertion and the option to use #2 Phillips drive bits for aftermarket adjustment supports flexible workflow; initial installation can favor strong bit engagement, while later tweaks can use widely available Phillips bits. Case hardening and lubrication support smooth driving and seating, so the screw can pull assemblies tight without binding in the wood during the final turns.
This screw has a round washerhead that is typically used in soft woods to prevent the head from sinking into the wood, which helps keep hardware and joint surfaces properly supported.
The patented serrated tooth turbo thread allows for quick starting, reduced splitting, and less drive torque, which speeds installation and helps protect wood around the fastener.
The screw is used in woodworking applications such as assembly, face frames, slides, hinges, and hardware, so it supports many cabinet and furniture fastening tasks.
The screw uses #2 square drive bits to insert, and #2 Phillips drive bits can be used for aftermarket adjustment, allowing use with both bit styles during a project.
Lengths of 3/4 inch and 1 inch are threaded fully, while all other sizes are threaded 2/3's from the bottom, which affects how the screw pulls mating pieces together.
The screw is case hardened and lubricated, which supports driving into wood with added surface hardness while the lubrication helps the threads advance smoothly.
This washer head assembly screw from Wurth pairs a round washerhead with a patented serrated tooth turbo thread, giving soft wood support and efficient driving in one fastener. By using #2 square drive bits for insertion and allowing #2 Phillips bits for aftermarket adjustment, it fits typical shop drivers while supporting later tuning of hardware and assemblies. For cabinet, face frame, slide, hinge, and hardware work that needs controlled head bearing and quick starting, this #8 x 3 washer head screw offers a focused option.
Sold In: 1500 Each
