Knape And Vogt Chrome Closet Rod For Storage Runs

Knape and Vogt chrome closet rod defines a straight, rigid hanging rail for closet and storage runs where a consistent diameter matters. This steel round closet rod has a 1-1/16 inch outer diameter, which sets a stable hanging surface that works predictably with hangers sized for common residential and commercial closets. The 6 foot length lets installers span typical cabinet or wall openings in one piece, which reduces joints that can shift over time. The chrome finish presents a smooth surface along the rod, which helps hangers slide without catching at rough spots and supports an orderly row of garments. Steel construction supports a solid feel in the rod, which helps it perform as a structural bar in closet layouts where the tubing also visually aligns multiple sections.

Key Closet Rod Details That Help On Site

• The 1-1/16 inch outer diameter creates a known interface for standard closet flanges, so layout measurements can be repeated from job to job without adjusting for odd sizes.
• The 6 foot length gives enough span for many single-door and double-door closets, so installers can cut to opening size while keeping waste predictable across multiple installations.
• The chrome finish provides a hard, smooth surface along the steel tubing, which supports easier sliding of hangers and keeps the rod looking consistent with other chrome closet components.
• The steel material forms the base of the round tubing, which provides a solid bar for hanging garments in closet and shelving systems where dependable support is expected.
• A wall thickness of 0.075 inch defines the tube cross-section, which balances material strength with manageable weight when cutting and handling rods on the job.
• An inside diameter of 29/32 inch sets the hollow core size, which matters when selecting cutting methods or when specifying end-support hardware sized around the interior opening.

Installation Use Of 1-1/16 Inch Closet Tubing

The 1-1/16 inch outer diameter on this Knape and Vogt closet rod gives installers a clear reference when choosing matching flanges and end supports built for that size, which streamlines hardware selection across a project. The 6 foot steel tube length provides enough material to cut multiple shorter rods or fit a full-span opening, which lets shop staff rough-cut in the shop and then trim to exact length on site. The chrome finish on the steel surface supports cutting and deburring without dealing with flaking coatings, so the installed rod can present a clean edge at both ends once it is set into the supporting closet hardware.

Where This 6 Foot Closet Rod Fits Best

Using Chrome Closet Rod In Storage Layouts

This Knape and Vogt chrome 1-1/16 inch diameter closet rod fits projects that call for steel round tubing as the primary hanging rail in closet, shelf, and garage organization systems. The 6 foot length suits reach-in closets and wardrobe cabinets where a single span keeps the hanging line visually straight. The chrome finish coordinates with other chrome closet components in the same project class, so the rod can run alongside matching flanges and support elements for a unified look. With a 0.075 inch wall thickness and 29/32 inch inside diameter, the tube geometry defines how the rod behaves when cut, drilled, or notched during fabrication, which helps shops repeat the same operations across many units.

Details That Support Repeatable Rod Installation

The defined 1-1/16 inch outer diameter gives carpenters and closet installers a fixed measurement for drilling cup locations or aligning flanges, which reduces layout variation between similar closets. The 6 foot steel length means cut lengths can be nested per job, which helps planners divide a stock rod into several smaller sections with minimal scrap. The chrome finish on the steel surface supports smooth travel of hangers after installation, which can reduce wear at contact points along the rod. A 0.075 inch wall thickness and 29/32 inch inside diameter also give metal fabricators consistent tube dimensions, so each cut, notch, or end preparation can be set up once and repeated for production runs of closet assemblies.

Common Questions About This Closet Rod Size

Choose This Rod For Consistent Closet Layouts

This Knape and Vogt chrome 1-1/16 inch diameter, 6 foot steel closet rod offers defined dimensions for closet and storage builds where repeatable layout matters. By working with its fixed outer diameter, wall thickness, and inside diameter, installers and shops can cut, mount, and align the tubing as a predictable hanging rail across similar projects.