Hickory Hardware Studio Series 3" (76 mm) Center to Center Stainless Steel Cup Pull, - P3013-SS

Hickory Hardware Studio Series Cup Pull For Cabinets

Hickory Hardware Studio Series cup pull gives cabinets a defined grip point with a stainless steel finish that presents as modern and clean on doors and drawers. This Belwith Keeler design uses a zinc die cast body, so the pull provides a solid feel while keeping weight manageable on typical cabinet fronts. The 3 inch center to center mounting dimension works for many North American layouts where this spread is standard for smaller drawers. A secondary 96 mm center to center option, noted in the description, lets the same part number serve projects that follow metric drilling patterns. The 4-7/8 inch overall width creates a wider hand contact area, which helps when opening heavier drawers. A 1 inch projection stands the cup pull off the face of the cabinet, leaving finger clearance while keeping the profile relatively low. The manufacturer part number P3013-SS ties this exact configuration to the Studio Series line.

Key Studio Series Cup Pull Details In Practice

• The zinc die cast material builds mass into the Hickory Hardware Studio Series cup pull, which gives drawers a confident handhold and supports repeated use in residential or shop environments.
• The stainless steel finish on this cup pull presents a neutral, brushed look that coordinates with many hinge and appliance finishes, helping maintain a consistent visual line across the run.
• The stated 3 inch and 96 mm center to center options allow this P3013-SS cup pull to align with both imperial and metric drilling setups, which supports mixed-layout jobs or staged remodels.
• The 4-7/8 inch overall width spreads the grip area across more of the drawer front, which can distribute pulling force and support smoother operation on wider fronts.
• The 1 inch projection dimension defines how far the cup pull stands off the door or drawer surface, creating finger clearance while limiting snag potential in tight walkways.

Mounting Dimensions And Pull Fit On Cabinets

The 3 inch center to center specification on this Hickory Hardware Studio Series cup pull identifies the spacing between the two mounting holes, which guides drilling on new fronts and hole alignment on replacements. The additional 96 mm center to center note supports layouts based on metric spacing, so the same part can follow existing metric boring jigs. With a width of 4-7/8 inch, the pull covers the span between fasteners and some surrounding area on the drawer or door, which can help conceal prior marks when swapping hardware of similar scale. The 1 inch projection figure defines how far the gripping edge stands off the cabinet face, helping installers visualize clearance relative to neighboring doors or countertop overhangs. These dimensions combine to position the P3013-SS cup pull as a practical choice where existing hole patterns and hand clearance drive selection.

Using The P3013-SS Cup Pull In Real Projects

Where This Studio Series Cup Pull Fits Best

This Belwith Keeler Hickory Hardware Studio Series cup pull fits well on cabinet doors and drawers that benefit from the 3 inch center to center mounting pattern, because it matches a common drilling standard in many kitchens and shops. When a project relies on metric system layouts, the referenced 96 mm center to center option lets the same part integrate with that pattern, which helps keep hardware style consistent across different cabinet lines. The stainless steel finish positions the pull alongside many contemporary hinge and appliance finishes, supporting visual continuity on face-frame or frameless cabinets. The 4-7/8 inch width suits small to medium drawers where a compact, cup-style handhold is preferred over a long bar, making this P3013-SS cup pull a straightforward choice for upper banks, vanity runs, and utility cabinets. The zinc die cast construction gives enough heft for these typical cabinet applications while maintaining a manageable profile.

Details That Support Repeatable Cabinet Results

The clearly defined 3 inch center to center dimension on the Hickory Hardware Studio Series cup pull allows repeatable drilling or boring using standard jigs, which helps installers maintain straight, level lines across multiple fronts. Because the description also notes a 96 mm center to center option, the same P3013-SS cup pull can be aligned to metric jigs on other runs, reducing layout changeover between imperial and metric sections of a project. The 1 inch projection keeps the grip close to the door surface, which can support clearance planning where drawers pass under countertops or next to adjacent cabinet doors. Zinc die cast construction contributes a consistent shape and edge detail from part to part, which matters when lining up several pulls across a bank and expecting the same hand feel at each position. The stainless steel finish ties these details together with a uniform appearance, supporting predictable visual results when repeating the hardware across an entire room.

Common Questions About The P3013-SS Cup Pull

Selecting This Cup Pull For Cabinet Projects

The Hickory Hardware Studio Series cup pull P3013-SS combines a 3 inch center to center layout, zinc die cast construction, and stainless steel finish to address both fit and appearance on typical cabinet runs. The additional 96 mm center to center note broadens use across metric-based drilling layouts while holding the same visual profile. With a 4-7/8 inch width and 1 inch projection, the pull balances grip space and clearance planning on drawers and doors. For projects calling for a Belwith Keeler cup pull that aligns with these dimensions and finish, this model delivers a focused option for consistent cabinet hardware runs.