Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Hickory Hardware Studio Series knob gives cabinets and drawers a square 1 inch by 1 inch pull point, which creates a consistent feel across doors and fronts in a run of cases. The satin nickel finish on this Belwith Keeler knob provides a neutral metallic look that works with a wide range of cabinet finishes in kitchens, baths, and shop-built casework. The knob is cast from zinc die cast material, so the body is solid and supports everyday use on frequently opened doors and drawers. A 1 inch projection pulls the hand slightly off the face of the cabinet, which helps protect finished surfaces from fingerprints during regular operation. The 3/4 inch square base keeps the bearing surface compact, which is useful when laying out hardware on narrow rails or small drawer fronts.
The Studio Series satin nickel knob uses an 8-32 thread size, which matches a common cabinet knob screw standard and allows straightforward drilling with typical bit sizes. The 1 inch projection from the door or drawer face sets a predictable standoff, which simplifies planning for clearances when doors open next to walls or adjacent cabinets. The knob body measures 1 inch square, so drilling can be centered easily on drawer fronts by referencing equal offsets from each edge. A 3/4 inch square base bears against the surface, which concentrates load into a compact footprint that helps maintain alignment once the knob is tightened. The Belwith Keeler part number P3014-SN clearly identifies this specific satin nickel, square-profile knob when matching existing hardware runs.
This 1 inch by 1 inch square knob suits cabinet doors and drawers where a compact, geometric pull is preferred over larger round designs. The satin nickel finish on the P3014-SN part works in spaces that use brushed fixtures, because its muted sheen coordinates with many hinges, faucets, and lighting trims specified in satin nickel tones. The zinc die cast construction from the Studio Series provides a solid-feeling knob, which is useful on frequently used kitchen or shop cabinets that see regular handling throughout the day. The 3/4 inch square base keeps the footprint small, so the knob fits comfortably on narrow face frames and smaller drawer fronts without visually crowding decorative profiles or applied moldings. The 1 inch projection keeps the grip consistent across all doors in a run, which helps maintain a uniform working clearance for hands.
The 1 inch square face dimension on this Belwith Keeler knob makes layout straightforward, because installers can center the knob using equal measurements from the edges on both doors and drawers. The 1 inch projection listed in the description establishes a repeatable offset from the cabinet face, which is helpful when matching existing knobs or aligning several Studio Series satin nickel knobs across a bank of fronts. The 3/4 inch square base creates a defined bearing point against the surface, which helps the knob seat firmly once tightened and reduces the tendency for rotation under regular pulling. The 8-32 thread size ties into common boring patterns for cabinet fronts, which simplifies using standard drilling templates on both new work and replacement jobs. The distinct P3014-SN identifier links all these dimensions and the satin nickel finish to a single part, which streamlines reordering when extending an existing installation.
The P3014-SN knob has a 1 inch length and 1 inch width, so it presents a square face that suits compact cabinet and drawer fronts.
The Studio Series satin nickel knob has a 1 inch projection, setting a consistent hand clearance off the cabinet face for everyday opening and closing.
The Studio Series knob has a 3/4 inch square base, which keeps the contact area compact for use on narrow rails and smaller drawer fronts.
The knob is made from zinc die cast material, giving it a solid body suitable for regular cabinet door and drawer use.
The Belwith Keeler P3014-SN knob has a satin nickel finish, providing a neutral metallic appearance that coordinates with many satin nickel fixtures.
This cabinet knob is specified with an 8-32 screw size, aligning with a common cabinet hardware thread used in many door and drawer fronts.
The Hickory Hardware Studio Series satin nickel knob combines a 1 inch square face, 1 inch projection, and 3/4 inch base into a compact cabinet pull that suits doors and drawers laid out on standard grids. The zinc die cast construction and satin nickel finish group this P3014-SN part into a consistent visual and functional hardware choice for casework built or supplied through Wurth Baer Supply.
Sold In: 1 Each
