Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Hickory Hardware Studio Series appliance pull gives you a 13 inch center to center grip on larger doors, so appliance and tall pantry fronts line up with substantial, consistent hardware across the run. Branded under Belwith Keeler, this pull fits into decorative hardware and moldings projects where an appliance pull is required rather than a standard cabinet handle, keeping the hardware class aligned with heavier fronts. A total length of 14-5/8 inches helps the pull span wider rail sections, which supports proportionally balanced layouts on full-height doors. The satin nickel finish provides a neutral, contemporary look that coordinates with many satin nickel hinges and knobs on the same job. Zinc die cast construction creates a solid-feeling pull body, which matters when the handle is routinely grabbed on heavier panels. This combination of length, center to center, and finish lets you repeat the same look across multiple appliance and cabinet fronts.
This satin nickel appliance pull uses a 13 inch center to center dimension, so boring for the two mounting points follows a straightforward linear layout on the door or panel. With a projection of 2 inches, the pull stands off the surface enough to provide hand clearance while still staying close to the face of the door. The 1-5/8 inch width helps distribute the grip area across more of the rail, which can be helpful on wider appliance or pantry fronts. An 8-32 x 1 inch screw size interfaces with the pull, giving a defined thread and length reference for selecting fasteners appropriate to the door thickness. Combined with the overall 14-5/8 inch bar length, these measurements support consistent placement up or down the stile so the hardware lines up across multiple fronts.
Belwith Keeler designates this Studio Series piece as an appliance pull, and its 13 inch center to center drilling supports that role by spanning a substantial section of the door. The 14-5/8 inch total length gives extra bar beyond each screw location, which helps the pull read correctly on tall appliance panels and full-height pantry doors. A width of 1-5/8 inches contributes to a more robust profile than many standard cabinet pulls, so the hardware visually matches thicker appliance fronts. The 2 inch projection positions the gripping surface off the face enough to grab comfortably, even when the front is flush with adjacent cabinets. Satin nickel finish ties the pull into satin nickel decorative hardware and moldings, creating continuity when you repeat the finish across doors, drawers, and surrounding cabinetry. Zinc die cast construction brings weight and rigidity to the handle body, which supports a confident feel when the door is opened and closed many times a day.
The defined 13 inch center to center distance provides a clear boring dimension for installers, so drilling jigs or shop templates can be set for repeat runs across multiple appliance or pantry fronts. An overall length of 14-5/8 inches offers a predictable amount of bar beyond each screw location, which helps when aligning hardware with door rails or neighboring pulls. The 2 inch projection works with adjacent cabinetry by holding the grip clear of proud moldings while still keeping it close to the face, which can assist in tight kitchen layouts. At 1-5/8 inches wide, the pull presents a consistent footprint that mates cleanly with flat door surfaces in the decorative hardware category. The specified 8-32 x 1 inch screw size defines the thread pattern used at each mounting point, which helps coordinate with drill sizes and tapping expectations when preparing the door or panel.
The Hickory Hardware Studio Series appliance pull uses a 13 inch center to center spacing, which sets the distance between the two mounting holes for consistent drilling.
The P3016-SN appliance pull has an overall length of 14-5/8 inches, giving extra bar beyond the 13 inch mounting points for better proportion on large fronts.
This satin nickel appliance pull is made from zinc die cast, providing a rigid handle body suited to frequent use on appliance or tall cabinet doors.
The Studio Series appliance pull projects 2 inches from the door face, giving hand clearance while keeping the grip relatively close to the panel.
This Belwith Keeler appliance pull is 1-5/8 inches wide, creating a broad grip area and a scaled appearance suited to larger appliance fronts.
This appliance pull is designed for an 8-32 x 1 inch screw size, setting the thread specification used at each mounting location on the handle.
Selecting this satin nickel appliance pull with 13 inch center to center drilling ties appliance and pantry fronts into the same Studio Series look across a project. The 14-5/8 inch length, 2 inch projection, and 1-5/8 inch width provide defined proportions that suit larger doors. Material specified as zinc die cast gives the handle a solid feel on heavier fronts. When these dimensions and finish line up with your layout, this Belwith Keeler P3016-SN pull offers a consistent, repeatable hardware choice for decorative hardware and moldings work.
Sold In: 1 Each
