5/16 hose assembly 5 foot from C.A. Technologies provides a compact air hose length that supports spray equipment setups where the run between gun and supply must stay manageable for control around workpieces. The air hose is specified with a 5/16 inch size, so it matches spray systems designed around this common hose dimension and helps maintain expected airflow through the line. The assembly is classified as an air hose assembly for spray equipment and spray guns, so it serves as a key connection in compressed air delivery for coating applications where predictable pressure helps pattern consistency. The manufacturer part number 53-112-5 identifies this configuration, which matters when matching hose assemblies across multiple spray stations or when standardizing replacement parts in a shop so that technicians can keep setups consistent from booth to booth.
The air hose working pressure of 200 psi defines the maximum operating level for compressed air in this assembly, so installers can configure regulators and compressor outputs within that range to keep the hose operating inside its intended load. The fluid hose working pressure of 750 psi is suited to higher pressure fluid circuits in spray systems, so technicians can route material lines where stronger pressure is needed to move coatings from pumps to spray guns. The textile reinforcement in the air hose and the braided high strength synthetic yarn in the fluid hose improve resistance to expansion, so the hoses stay more dimensionally stable when pulled through supports or around equipment. The specified temperature ranges for air and fluid hoses also support routing near equipment that generates heat, helping the lines remain functional in typical spray booth environments.
This air hose assembly is categorized under spray equipment and spray guns, so it is aimed at compressed air delivery and related lines in coating applications. The 5 foot length suits short runs between spray guns and nearby regulators or manifolds, which is useful when the operator wants to limit hose slack around workpieces and fixtures. The air hose temperature range from -20 to +190 degrees F means it can operate in many indoor shop environments where overnight temperatures fall and compressor discharge temperatures rise, so the same assembly can serve across different times of day. The oil resistant smooth red synthetic rubber casing on the air hose is well suited to compressor areas where lubricated air lines are present, because incidental contact with oil mist on surfaces is less likely to affect the hose exterior. The fluid hose portion using a smooth black synthetic rubber casing and oil resistant design makes sense around spray guns and pumps where coating drips or solvent splashes may reach the hose surface during cleaning or color changes.
The 5/16 inch air hose size is a practical match for spray guns and regulators designed for that diameter, because it supports consistent airflow and pressure drop characteristics that operators expect when dialing in spray patterns. The 200 psi working pressure rating on the air hose gives a defined ceiling for shop air systems feeding this assembly, which helps keep the hose within its intended stress range during long coating runs. The textile reinforcement in the air hose and braided high strength synthetic yarn in the fluid hose limit ballooning under pressure, so fittings stay more secure and hose routing remains predictable when lines are pressurized. The nylon 11 tube in the fluid hose, specified as silicone-free, is important where coatings or finishing processes are sensitive to silicone contamination, because the tube composition supports material purity through the fluid path. The fluid hose working pressure of 750 psi also supports use with pumps that require higher line pressure, helping sustain steady material delivery to the spray gun when heavier coatings or longer fluid runs are part of the system layout.
This product is an air hose assembly from C.A. Technologies classified under spray equipment and spray guns, so it serves as a hose solution for spray-related compressed air and associated lines.
The air hose has a 200 psi working pressure, so air systems feeding this hose are set up to operate within that pressure to keep the hose within its specified load range.
The air hose operates from -20 to +190 degrees F, so it remains usable in colder indoor conditions and in warmer areas near compressors typical of many spray shops.
Textile reinforcement in the air hose strengthens the wall, so it better resists expansion at 200 psi and keeps its shape when routed along supports or around equipment.
The fluid hose uses a nylon 11 silicone-free tube, braided high strength synthetic yarn reinforcement, an oil resistant smooth black synthetic rubber cover, and a 750 psi working pressure to support higher pressure coating lines.
The nylon 11 silicone-free tube in the fluid hose keeps the fluid path free of silicone, which supports applications where coating performance depends on avoiding silicone contamination.
This 5/16 hose assembly 5 foot with textile reinforced air hose, oil resistant smooth red synthetic rubber casing, and 200 psi working pressure offers a defined set of characteristics for spray equipment layouts. The paired fluid hose with nylon 11 silicone-free tube, braided high strength synthetic yarn, oil resistant smooth black synthetic rubber cover, and 750 psi working pressure adds capability for higher pressure material delivery. Using the specific manufacturer part number 53-112-5 from C.A. Technologies through Wurth Baer Supply helps keep hose selections consistent across spray booths and supports repeatable performance when setting up or updating spray lines.