Amerock Rochdale Graphite Knob For Cabinets

Amerock Rochdale graphite knob brings the Rochdale Collection design into a compact 1-1/4 inch diameter pull for cabinet doors and drawers. The knob uses zinc die-cast construction, which gives installers a solid, consistent feel that supports repeatable results across a run of doors or fronts. Its 1-1/4 inch width matches the listed diameter, so layout measurements remain straightforward when planning uniform knob placement. The graphite finish provides a dark, architectural look that works with the collection's industrial styling, helping tie together cabinets that use similar Rochdale hardware. A projection of 1-1/8 inch sets the hand clearance off the cabinet face, which matters when working around thicker door profiles or overlay fronts. The 1-1/16 inch base diameter spreads contact at the mounting point, which helps the knob sit cleanly against the surface for a finished appearance.

Key Rochdale Cabinet Knob Details For Projects

• The 1-1/4 inch (32 mm) diameter gives a defined grip area, which helps when aligning multiple knobs across wide cabinet banks or tall pantry doors.
• The 1-1/8 inch projection sets a predictable stand-off, which supports consistent clearance for fingers on drawers and doors with varying edge profiles.
• The 1-1/16 inch base diameter creates a stable footprint at the mounting hole, which helps the knob register square against the cabinet face during tightening.
• The zinc die-cast material provides a uniform molded body, which supports repeatable appearance across a full kitchen or casework installation.
• The graphite finish ties directly to the Rochdale Collection, which helps match this knob with other Rochdale pieces in the same project.
• The Amerock BP53710GPH part number identifies this exact graphite Rochdale knob, which helps reorder or specify it consistently across job documents.

Rochdale Knob Fit, Size, And Mounting Details

The Amerock Rochdale series knob uses an 8-32 threaded connection, which aligns with standard cabinet knob mounting methods on most drilled cabinet faces. At 1-1/4 inch length or diameter with a 1-1/8 inch projection, the knob extends far enough from the surface to clear typical door and drawer front thicknesses while keeping the profile compact. The 1-1/16 inch base diameter lets the knob cover standard bore edges cleanly, supporting a neat finish on both painted and stained fronts where the mounting hole must remain hidden. Because the width is also 1-1/4 inch, installers can treat the knob as a balanced circle when centering on narrow rails, which can simplify marking and drilling during layout work.

How This Rochdale Knob Supports Real-World Work

Using The Rochdale Cabinet Knob In Projects

The Rochdale Collection graphite knob is designed as decorative cabinet hardware, so it suits applications where a 1-1/4 inch diameter pull is appropriate on doors or drawers. The industrial styling with rivet-influenced details gives cabinets a more architectural look, which matters on projects calling for a masculine design aesthetic. Because it is part of Amerock's Rochdale line, the knob aligns visually with other Rochdale pieces, allowing a uniform hardware story across kitchens, baths, or built-ins based on that collection. The zinc die-cast material helps maintain consistent detailing from knob to knob, which is useful when the job calls for multiple units across long cabinet runs or matching casework. The graphite finish supports darker color schemes, giving hardware contrast on lighter fronts or a more subtle tone-on-tone effect on darker finishes.

Details That Help Achieve Consistent Results

The specified 8-32 x 1 inch screw size sets expectations for the threaded interface, which helps installers match the knob to standard cabinet drilling practices. The 1-1/4 inch diameter and identical width give a clear center point to work from, which supports accurate alignment when laying out knobs relative to door stile widths or drawer heights. A 1-1/8 inch projection balances clearance and profile, so the knob stands off enough for fingers while staying close enough to avoid feeling bulky on smaller fronts. The 1-1/16 inch base diameter means the contact ring remains slightly smaller than the gripping head, which creates a stepped look that visually seats the knob against the cabinet surface. With the Amerock BP53710GPH designation clearly tied to the Rochdale graphite finish, specifiers can call out this exact knob across drawings, cut lists, and order forms, helping maintain consistency from design through installation.

Common Questions About The Rochdale Graphite Knob

Selecting This Amerock Rochdale Knob For Work

The Amerock Rochdale Series Graphite 1-1/4 inch Diameter Knob BP53710GPH combines zinc die-cast construction, graphite finish, and 1-1/8 inch projection into a compact pull sized for doors and drawers. When a project calls for Rochdale Collection styling with an industrial, architectural feel, this knob delivers that look in a standard 8-32 threaded format suited to cabinet work. For jobs needing consistent hardware across multiple cabinets, this specific part number provides a clearly defined option to specify and deploy.