Berenson Bravo Series 6-5/8" (169 mm) Center to Center Polished Chrome Tab Pull, - 1066-4026-P

Berenson Bravo Series Tab Pull For Clean Lines

Berenson Bravo Series tab pull gives you a low-profile way to open doors or drawers while keeping faces clean and flat. This pull is part of the Bravo collection, so its styling stays consistent across related pieces on a job. The aluminum construction keeps weight down while still providing a solid gripping edge, which helps when you are lining up multiple pulls across cabinet runs. A polished chrome finish reflects surrounding surfaces for a bright, contemporary look that works well on modern cabinet fronts. The 9-1/16 inch overall length spans more of the door or drawer, creating a defined visual edge that ties sections together. With a 6-5/8 inch center to center dimension, this pull matches common drilling patterns for wider fronts. The tab style mounts at the edge, so the pull sits proud only where you need a handhold.

Key Bravo Edge Pull Details That Matter On Site

• The Bravo collection identity keeps the tab pull style coordinated with other Bravo pieces on a project, which helps maintain a unified look across all fronts.
• Aluminum material provides a light but sturdy pull body, which is helpful when you are installing multiple units on large banks of cabinets.
• The polished chrome finish gives a bright, reflective surface that visually pairs with other polished chrome decorative hardware on doors and drawers.
• An overall length of 9-1/16 inches lets the pull visually anchor wider drawer fronts so the hardware does not get lost against the surface.
• The 3/4 inch width concentrates the gripping area at the edge, allowing the pull to remain visually slim while still providing a defined finger contact point.
• A 1-3/4 inch projection creates space for fingers behind the tab, which helps users get a comfortable grip without crowding the cabinet face.
• The 6-5/8 inch center to center dimension establishes a stable two-point mount that spreads load over a wider section of the front.
• Manufacturer part number 1066-4026-P identifies this exact Bravo edge pull, which supports consistent reordering for repeat jobs or service calls.

Installation Sizing And Hole Layout For This Pull

The 6-5/8 inch center to center measurement defines the exact spacing between mounting holes, so you can lay out drilling accurately before committing to a run of fronts. Using the 9-1/16 inch overall length as a reference, you can position the pull relative to door or drawer edges to keep reveals even from unit to unit. The 3/4 inch width keeps the pull focused along the edge, making it easier to align several pulls in a straight visual line. With a 1-3/4 inch projection, the pull stands out far enough that fingers clear the front, which can reduce contact marks around high-use openings. The aluminum construction keeps each pull relatively light, which is useful when installing on thinner fronts that still need a firm grip point.

Using The Bravo Edge Pull In Cabinet Projects

Where This 6-5/8 Inch Center Pull Fits Best

The 6-5/8 inch center to center dimension positions this pull well on medium to wider cabinet doors and drawers where a short pull might look undersized. The 9-1/16 inch overall length lets it span more of the front, which visually anchors wider faces and helps balance tall doors. Its tab style works along the edge of fronts, so it pairs naturally with slab or flat-panel designs that rely on a clean face with minimal projection hardware. The polished chrome finish ties in with other polished chrome decorative pieces, so it can run across a full kitchen or bath layout without visual breaks. Because it belongs to the Bravo collection, it can be matched with other Bravo items to carry the same design language from upper cabinets down to base units.

Why These Dimensions Support Repeatable Install Results

The defined 6-5/8 inch center to center spacing gives a precise drilling target, which supports jigs and templates when you are installing multiple pulls on a bank of fronts. The 9-1/16 inch overall length helps you visually center the pull on doors and drawers, making it easier to maintain symmetry across adjacent cabinets. A 3/4 inch width keeps the body compact so the pull sits close to the edge, which helps avoid interference with neighboring doors on tight reveals. The 1-3/4 inch projection provides room for a full finger grip, which improves day-to-day use when doors are opened repeatedly. Aluminum construction keeps the mass low, which can be helpful when fastening into thinner or lighter cabinet materials that still need solid-feeling hardware. The polished chrome finish presents a consistent surface that visually hides minor fingerprints in reflection rather than drawing the eye to the pull body.

Common Questions About This Berenson Bravo Pull

Select This Bravo Edge Pull For Consistent Layouts

The Berenson Bravo Series 6-5/8 inch center to center tab pull brings known dimensions to layout work, with a 9-1/16 inch length, 3/4 inch width, and 1-3/4 inch projection all clearly defined. Aluminum construction and a polished chrome finish supply a light but solid-feeling grip in a bright, modern look. For projects where you want a coordinated Bravo collection appearance and repeatable drilling across fronts, this pull offers a clear set of measurements to work from on each cabinet.