1-5/16" Diameter Closed Flange for Round Closet Rods, Pin Mount, Dull Brass Finish

1-5/16 Inch Diameter Closed Flange For Round Rods

1-5/16 inch diameter closed flange describes a Pro Value Series flange that holds a 1-5/16 inch outside diameter round closet tube, so it matches standard heavy round rods and supports consistent layouts across a closet run. This closed flange design supports the end of the rod, so the tube seats positively in the flange and helps maintain alignment. The flange is made of a zinc alloy, so it provides a solid metal bearing surface for the rod and stands up to normal closet use. The dull brass finish on the flange provides a muted brass tone, so it coordinates with other dull brass closet hardware and gives a uniform appearance. This part is identified by manufacturer part number 54231 47 039, so it can be specified or reordered accurately when building or extending a closet system.

Key Closet Rod Flange Details For Installers

• The zinc alloy construction provides a rigid body for the flange, so it supports the 1-5/16 inch rod without deforming under typical hanging loads.
• The flange holds a 1-5/16 inch outside dimension tube, so it fits common round closet rods and simplifies matching rods to mounting points.
• The closed flange style captures the end of the rod, so the tube is positively located and less prone to end movement along the wall.
• The dull brass finish delivers a non-gloss brass appearance, so visible hardware aligns with other dull brass components in the closet.
• The piece is part of the Pro Value Series line, so it aligns with other Pro Value Series closet rods and fittings when building out a coordinated system.
• The product sits in the Closet Rods & Flanges class, so it works as the rod termination or support point within a typical closet layout.

Pin Mount Flange Layout And Fastening Details

The flange has two pins, 32mm on center, for 5mm bore holes, so it fits systems drilled on the 32mm line and lets the pins register directly in 5mm bores for positive location. A center screw hole in the flange provides the main fastening point, so the installer can drive a screw through the flange body for a secure hold into the mounting surface. This combination of two locating pins and a center screw hole allows the flange to sit square to the closet side panel, so the rod runs straight between flanges and hangs garments evenly.

Using This Pro Value Series Flange In Closets

Closet Rod Support Where 1-5/16 Inch Rods Are Used

This Pro Value Series closed flange is designed to hold a 1-5/16 inch outside dimension tube, so it works wherever that rod size is specified in a closet or storage run. Because the flange is closed, the end of the round rod seats in the flange body, so each rod end has a defined stop that controls overall rod length between panels. That closed geometry helps maintain clearance from walls or doors at the end of the run, because the rod position is dictated by the flange rather than by eyeballing the cut. As part of the Closet Rods & Flanges product class, this component serves as the rod termination at side panels or end supports, so installers can build consistent sections across multiple openings in a closet system.

Pin Mount And Finish Details That Support Consistency

The two pins on 32mm centers are sized for 5mm bore holes, so the flange keys directly into standard system holes and reduces layout time when working on 32mm-based closet panels. Those pins act as alignment guides before the center screw is driven, so the flange seats level and keeps the 1-5/16 inch rod parallel to shelves above or below. The center screw hole through the flange gives a direct fastening point into the substrate, so the installer gains a strong mechanical connection behind the decorative dull brass face. The dull brass finish keeps the mounting hardware visually subdued against matching rods and components, so the installation reads as a single coordinated Pro Value Series assembly. With manufacturer part number 54231 47 039 clearly identifying the piece, shops can standardize this flange in cut lists and ordering systems, so repeat jobs and future expansions use the same rod support layout.

Common Questions About This Closet Rod Flange

Select This Flange For 1-5/16 Inch Rod Runs

This Pro Value Series 1-5/16 inch diameter closed flange in dull brass combines a zinc alloy body, 32mm-on-center 5mm pins, and a center screw hole, so it supports round closet rods with accurate alignment and a coordinated finish across the closet system.